OST OmniConverter GPoE+/S, Руководство пользователя

Страница: 3 / 10

DIP-switch Bank Locations
The table below provides a description of each DIP-switch position and function.
Switch 1 Fiber, 1 RJ-45 1 Fiber, 2 RJ-45 2 Fiber, 1 RJ-45 2 Fiber, 2 RJ-45
1
Port 1 Fiber
Speed
Port 1 Fiber
Speed
Port 1 Fiber
Speed
Port 1 Fiber
Speed
2 N/A N/A
Port 2 Fiber
Speed
Port 2 Fiber
Speed
3
Port 2 RJ-45
AUTO/MAN
Port 2 RJ-45
AUTO/MAN
Port 3 RJ-45
AUTO/MAN
Port 3 RJ-45
AUTO/MAN
4
Port 2 RJ-45 Speed
(Only in MAN mode)
Port 2 RJ-45 Speed
(Only in MAN mode)
Port 3 RJ-45 Speed
(Only in MAN mode)
Port 3 RJ-45 Speed
(Only in MAN mode)
5
Port 2 RJ-45 Duplex
(Only in MAN mode)
Port 2 RJ-45 Duplex
(Only in MAN mode)
Port 3 RJ-45 Duplex
(Only in MAN mode)
Port 3 RJ-45 Duplex
(Only in MAN mode)
6 Pause Capability Pause Capability Pause Capability Pause Capability
7 RJ-45 Port 2 PoE/PSE RJ-45 Port 2 PoE/PSE RJ-45 Port 3 PoE/PSE RJ-45 Port 3 PoE/PSE
8 N/A RJ-45 Port 3 PoE/PSE N/A RJ-45 Port 4 PoE/PSE
9 PSE Configuration Type PSE Configuration Type PSE Configuration Type PSE Configuration Type
10 PSE Configuration Type PSE Configuration Type PSE Configuration Type PSE Configuration Type
11 N/A N/A PSE Configuration Type PSE Configuration Type
12 Link Mode Selection Link Mode Selection Link Mode Selection Link Mode Selection
13 Link Mode Selection Link Mode Selection Link Mode Selection Link Mode Selection
14 PSE Reset PSE Reset PSE Reset PSE Reset
15 N/A N/A Redundant Fiber Link Redundant Fiber Link
16 N/A N/A Return to Port 1 Return to Port 1
DIP-switch Definitions
SW1 and SW2: F/O Speed “100/1000” DIP-switch
The module supports 1000BASE-X and 100BASE-FX SFPs. These DIP-switches
are used to configure the unit for the speed of the installed SFPs. Setting these DIP-
switches to the Down “1000” position enables the fiber port to accept 1000BASE-X
Page 5
SFPs. Setting these DIP-switches to the Up “100” position enables the fiber port
to accept 100BASE-FX SFPs.
When an RJ-45 transceiver is installed in a SFP receptacle or for fixed fiber
models, setting this DIP-switch to Up “100” position enables the port to operate at
100Mbps*.
These DIP-switches are ignored when using Omnitron branded fiber SFPs. The
module automatically configures the fiber port to the correct speed.
*Special compatibility mode for the fixed fiber models only.
SW3, SW4 and SW5 RJ-45 Configuration DIP-Switches
SW3
RJ-45
AN/Man
SW4
RJ-45
100/10
SW5
RJ-45
FDX/HDX
RJ-45 Mode of Operation
AN 10 or 100 FDX or HDX
The RJ-45 port is set to auto-negotiation with the following modes
advertised: 1000FDX, 1000HDX, 100FDX, 100HDX, 10FDX,
10HDX
MAN 100 FDX The RJ-45 port is set to manual negotiation and is forced to 100FDX.
MAN 100 HDX The RJ-45 port is set to manual negotiation and is forced to 100HDX.
MAN 10 FDX The RJ-45 port is set to manual negotiation and is forced to 10FDX.
MAN 10 HDX The RJ-45 port is set to manual negotiation and is forced to 10HDX.
RJ-45 Port Configuration Matrix
SW6 - Pause “On/Off” DIP-Switch
In auto-negotiation mode, setting this DIP-switch to the Up “On” position allows the
unit to advertise Symmetrical and Asymmetrical Pause capability. In auto-negotiation
mode, setting the DIP-switch to the Down “Off” position allows the unit to advertise
no Pause capability. In the manual mode, this DIP-switch determines the Pause
behavior.
SW7 - Power Sourcing Function, RJ-45 Port
The OmniConverter automatically detects the attached PD and provides the
equipment with the necessary power.
This DIP-switch controls the power sourcing function for Port 2 on the single-fiber
models and Port 3 on all other models (see DIP-switch Definition table on page
5). When this DIP-switch in the Down “On” position, the power sourcing function
is enabled. When the DIP-switch is in the Up “Off” position, the power sourcing
function is disabled.
Switch Position Description DOWN UP
7 RJ-45 Port 2 or 3 PoE/PSE Enabled (ON) Disabled (OFF)
8 RJ-45 Port 3 or 4 PoE/PSE Enabled (ON) Disabled (OFF)
Power Sourcing Function
Page 6