manualshive.com logo in svg

OSSIA NVR5 Series, Руководство пользователя

Поделиться
Скачать
OSSIA NVR5 Series Скачать руководство пользователя страница 52

Record & Disk Management 

                   

   

  User  Manual

 

 

51 

 

7

 

Record & Disk Management   

7.1   Record Configuration: 

7.1.1   Mode Configuration: 

Please format the HDDs to enable recording (refer to 7.5 Disk Management for details). 

 
The Ossia recording interface was redesigned to be clearer and easier to configure. It is based 
on  statistics  showing  that  most  users  configure  the  recording  to  work  all  year  long  in  24x7 
schedule – the “Auto” mode is the best choice for these users. “Manual” mode is for users who 
wish to customize the recording/schedule configuration. 
 
Click Start

Settings

Record

Mode Settings to go to the mode settings interface. 

 

 

 

➢

 

Auto Mode: The standard setting will include the following presets: 

 

Motion Record

: Record will start upon 

Motion Alarm

 under 24x7 schedule for all channels.   

Sensor Record

:

 

Record will start upon 

Sensor Alarm

 under 24x7 schedule for all sensors. 

Motion  Sensor Record

:

 

Record will start upon 

Motion or Sensor Alarms

 under 24x7 

schedule for all channels and sensors. 

Always  (24

ⅹ

7)  Record  +  Motion  Record

:

 

All  the  channels  will  be  recorded  continuously. 

Motion alarms

 will be marked in the event list and trigger “Event Record”.

 

Always  (24

ⅹ

7)  Record  +  Sensor  Record

:  All  the  channels  will  be  recorded  continuously. 

Sensor alarms

 will be marked in the event list and trigger “Event Record”.

 

Always (24

ⅹ

7)  Motion  Sensor Record

:

 

All the channels will be recorded 

continuously. 

Motion  and  sensor  alarms

  will  be  marked  in  the  event  list  and  trigger  “Event 

Record”. 

Содержание NVR5 Series




















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды