OSS OSS-PCIe-HIB38-x16 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 23

OSS OSS-PCIe-HIB38-x16 Скачать руководство пользователя страница 14

One Stop Systems

OSS-PCIe-HIB38-x16

| 14

3 Installation Procedures

Host adapter

(aka: HIB - Host Interface Board)

The host adapter (aka: Host Interface card) is installed into the host computer’s PCIe x16 slot. The host cable adapter (Part # OSS-PCIe-HIB38-
x16-H) allows communication between a processor and an I/O point.

Target adapter

(aka: Target Card, Expansion Interface Card)

The target card(Part# OSS-PCIe-HIB38-x16-T) fits into an OSS custom slot backplane and extends the PCIe bus to a single add-in board via a PCIe
x16 cable. The “Target Card” can only be installed in a designated “Upstream slot” on OSS expansion backplane.

The following steps will guide you through the installation of your OSS-370 Host and Target cards

3.1

Configure Dipswitches

Prior to using the HIB card, it needs to set the Dipswitch to appropriate operating mode. There are two standard modes, Host mode and Target
mode.

3.1.2

Set 1

st

HIB to Target Mode

Configure HIB to Target mode by the dipswitches to their corresponding setting, see photo below

3.1.3

Set 2

nd

HIB to Host Mode

Configure the 2

nd

HIB card to Host mode, see dipswitches settings below.

«
...
12
13
14
15
16
...
»

Содержание OSS-PCIe-HIB38-x16
























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды