CC30/KH30/ME30/MN30
FILE CABINET
ASSEMBLY INSTRUCTIONS
© Office Star Products October 2008
IMPORTANT NOTE:
1. Use hand tools only for assembly as power tools may cause damage
2. Carefully remove any staples used for packaging.
3. Phillips Screwdriver also needed for assembly (not provided)
STEP 1 & 2
2L
13
2R
3
5
4
10
9
12
7R
6
14
1
DETAIL A
11
8
PART
QTY
1. Top . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Side Panel (2L & 2R) . . . . . . . . . . 2
3. Bottom Frame . . . . . . . . . . . . . . . . 1
4. Back Panel . . . . . . . . . . . . . . . . . . 1
5. Drawer Front . . . . . . . . . . . . . . . . . 2
6. Drawer Bottom . . . . . . . . . . . . . . . . 2
7. Drawer Side (7L & 7R) . . . . . . . . . 4
8. Drawer Back . . . . . . . . . . . . . . . . . 2
9. Knob . . . . . . . . . . . . . . . . . . . . . . . 2
10. Allen Screws . . . . . . . . . . . . . . . . 8
11. Short Wood Screws . . . . . . . . . . . 8
12. Long Wood Screws . . . . . . . . . . 24
13. Short Screws . . . . . . . . . . . . . . . . 2
14. L Brackets . . . . . . . . . . . . . . . . . . 2
15. Allen Wrench (Not Shown) . . . . . 1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
DraWEr aSSEMBLy:
STEP 1. With groove facing inwards, attach Drawer Sides (7L & 7R) to Drawer Back (8) using three Long Wood Screws (12) for
each Drawer Side (7) .
Slide Drawer Bottom (6) into grooves of Drawer Sides (7L & 7R) and Drawer Back (8) .
STEP 2 Attach Drawer Front (5) to Drawer Sides (7L & 7R) using three Long Wood Screws for each Drawer Side (7) .
FULLY TIGHTEN ALL SCREWS. Attach Knob (9) to Drawer Front (5) by using one Short Screw (13) .
Repeat
STEP 1& 2 for second Drawer . FULLY TIGHTEN ALL SCREWS.
CaBInET aSSEMBLy:
STEP 3. Place Top (1) face down on soft surface . Align one Side Panel (2L) to side of Top (1) so that Back Panel (4) grooves
align . Secure using two Allen Screws (10) .
DO NOT FULLY TIGHTEN ALL SCREWS COMPLETELY.
STEP 4. Insert Back Panel (4) in grooves of Top (1) and installed Side Panel (2L) . Align grooves in Bottom Frame (3) to Back
Panel (4) and attach to installed Side Panel (2L) using two Allen Screws (10) .
DO NOT FULLY TIGHTEN ALL SCREWS.
Align remaining Side Panel (2R) to Top (1), Bottom Frame (3), and Back Panel (4) .
Secure using Allen Screws (10) .
APPLY FIRM PRESSURE TO ALIGN AND FULLY TIGHTEN ALL SCREWS.
STEP 5. Install one L Bracket (14) to each back inside corner of assembled cabinet using four Short Wood Screws (11) for
each L Bracket (14) .
FULLY TIGHTEN ALL SCREWS.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CABINET.
STEP 3 & 4
STEP 4
12
7L
DETAIL B
DETAIL C
DETAIL D
