E
L
E
C
T
R
O
N
IC
A
L
LY
C
O
N
T
R
O
LLE
D
S
IN
G
LE
P
O
IN
T
LO
C
K
O
R
LA
T
C
H
U
L
MOTOR
CONNECTOR
RESET
BUTTON
TERMINAL BLOCK
(FOR REMOTE SWITCH)
CPU PC
BOARD
ASSEMBLY
RED
WIRE
BLACK
WIRE
1580 JAYKEN WAY
CHULA VISTA, CALIFORNIA. 91911
(619) 628-1000 FAX (619) 628-1001
SECURITY
D E V I C E S
Copyright
2001 OSI Security Devices Inc. All Rights Reserved
OMNILOCK is a Registered Trademark of OSI Security Devices Inc. FALCON is a trademark of Falcon Lock Co.
11523 Rev A
SECTION 5: INSTALL THE STRIKE
SECTION 7: REMOTE SWITCH
a. Remote operation of the System may be accomplished by a momentary Switch
closure. This may be desirable for someone monitoring a protected entrance,
such as a receptionist. Momentarily pressing the Switch will cause the System
to go through a normal unlock and lock sequence. If the Switch is held closed,
the open time will be extended.
b. Connect a twisted pair of wires from the Terminal Block on the PC Board to a
normally open momentary contact Switch. Plan the route for your wire and the
access route through the door to the PC Board in the OMNILOCK Module. Plan
for disconnecting the wires in the module area so that the System can be
removed from the door to change the Batteries as required. Refer to Fig.14.
(Website: WWW.OMNILOCK.COM)
OMNILOCK
SWITCH
TWISTED
PAIR
OMNILOCK
ACCESS CONTROL SYSTEMS
SECURITY
D E V I C E S
WARNING: THIS PRODUCT IS NOT WARRANTED FOR
OUTDOORS USE!
NOTE: A DOOR-CLOSER IS HIGHLY RECOMMENDED
FOR USE WITH THIS PRODUCT.
THIS PRODUCT IS NORMALLY FACTORY-PACKED
FOR RIGHT-HAND 1-3/4” TO 2” THICK DOORS.
TO CHANGE HAND OF LOCK, SEE
INSTRUCTION SECTION 2.
LOCK
CONNECTOR
(Routes through
the slot in the
Door)
SCREW
POST
OUTER TRIM
ASSEMBLY
INTERCHANGEABLE CORE (I.C.)
I.C. CORE
(NOT SUPPLIED)
CONTROL KEY
(NOT SUPPLIED)
I.C. CYLINDER
WITH CAM
NYLON
WASHER
SCREW
FLAT HEAD
#12 X 1”
(2-REQD)
STRIKE
BOX
STRIKE
SCREW
FLAT HEAD
#12 X 1” (2-REQD)
WASHER
THUMB TURN
INSIDE
LEVER
SCREW, FLAT
HEAD #6X1/2”
(2-REQD)
SCREW
FLAT HEAD
#8X2-1/4”
(2-REQD)
INSTALLER NOTES: Leave these instructions and other Documents with the User.
CYLINDER
WITH CAM
WAVY
WASHER
HOUSING
ASSEMBLY
KEY
SCREW
PAN HEAD
#6-32X1/4”
STANDOFF
#8-32X1”
(2-REQD)
AA ALKALINE
BATTERY, 1.5V
(4-REQD)
BATTERY
COVER
GASKET
SEMS #4-40X1/4”
PAN HEAD
SCREWS,
FLAT HEAD
#8-32X3/8”
LG (2-REQD)
GROUND
SPRING
CYLINDER
COLLAR
BACK
PLATE
ELECTRONICS MODULE
CONNECTOR
SPINDLE & SPRING
ASSEMBLY
SCREW, PAN HEAD TORX
#8-32X1-1/2” FOR 2” THICK DOOR
#8-32X1-1/4” FOR 1-3/4” THICK
DOOR (2-REQD)
LOCK
FACE
PLATE
SCREW, FLAT
HEAD #10-32 X 2”
(2 REQD)
INNER INSERT
ASSEMBLY
SPINDLE & SPRING
ASSEMBLY
PG. 8 OF 8
PG. 1 OF 8
INSTALLATION INSTRUCTIONS
FOR OM100, OM300,
AND OM500 SERIES
NON-WEATHERIZED,
MORTISE
LOCKSETS
USING
FALCON
™
LM SERIES LOCKS (LEVER)
a. Draw a vertical line on the Door Frame 1/2 the Door thickness
from the Door Stop. Refer to Fig.13.
CAUTION: Allow for paint buildup or weather stripping if required.
b. Select the Strike with the proper hand condition and align the
bottom edge of the Strike Lip with the mark on the Door Frame
and align the center of the mounting holes in the Strike with the
vertical line on the frame. Using the Strike as a template, mark the
Door Frame.
c. Using the Strike Box as a template, mark the Door Frame.
d. Mortise the Frame to accept the Strike and Strike Box.
e. Install the Strike Box and the Strike and secure with the Screws.
COLLAR
SET
SCREW
ALIGNMENT
MARKS
STRIKE BOX
SCREW
#12X1
STRIKE
FIG.13
FIG.14
ALIGMENT
MARKS
SECTION 6: PROGRAM THE LOCK
IMPORTANT: To avoid unauthorized access, it is important to program a new Master Code.
For programming instructions refer to the Quick Reference Guide shipped with this product or to the OMNILOCK
User Guide which may be ordered by calling Customer Service at 619-628-1000 or it may be downloaded from out
website http:/omnilock.com/files/om135man.pdf
DOOR HANDLING
RIGHT HAND SHOWN
DOOR HAND DETERMINED FROM OUTSIDE
LEFT
HAND
RIGHT
HAND
INSIDE
OUTSIDE
INSIDE
OUTSIDE
RIGHT HAND
REVERSE
BEVEL
LEFT HAND
REVERSE
BEVEL
