background image

Osborne Big Wheel hog feeders are packaged carefully and compactly to ensure 

their safe arrival at minimum cost. Each part was quality inspected prior to 

shipment and each carton was carefully packed to ensure that all necessary 

parts were present for the assembly.

UNPACKING

Upon receiving your shipment, check the cartons for in transit handling damage. 

ALERT THE DELIVERING CARRIER IMMEDIATELY if damage is discovered. 

Continue unpacking only after the carrier has acknowledged the damage and 

potential loss of contents.

NOTICE

All loss or damage in transit is the responsibility of the delivering carrier, 

NOT OSBORNE INDUSTRIES. To protect your rights in the event of damage 

or loss, 

sign the delivery waybill only after the carrier has acknowledged in writing that damage or loss has occurred.

 In the event that damage is 

revealed only after unpacking is complete, notify the delivering carrier immediately and request an inspection of the damaged merchandise before proceeding.

1.  Install axle (Item 10) into center recess of trough (Item 12). Drill 3/16-in. 

holes through trough using axle as guide. Secure using 10-24 flat head 

machine screws and 10-24 nuts (Items 11 & 13).

2.  Place 3/4-in. feed wheel washer (Item 9) on axle followed by feed wheel 

(Item 8). If wheel does not turn freely, check for and remove paint or 

galvanizing residue.

3.  Force trough divider cage (Item 6) onto trough using rubber mallet. 

Ensure no gaps exist between cage and trough as fiberglass could break 

when bolts are installed. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drill 5/16-in. holes through trough using cage as a guide. Install 5/16 

x 7/8-in. bolts and 5/16-in. nuts (Items 7). 

DO NOT OVER-TIGHTEN 

BOLTS ON FIBERGLASS.

4.  Attach 5/16 x 1 3/4-in. cage tightener bolt and 5/16-in. hex nut (Items 4) 

into top of cage divider but do not tighten.

RLX-0525_N

RF2 SERIES

FINISH CONFINEMENT FEEDER

Assembly & Operating Instructions

Big Wheel

®

 Hog Feeders

Required Tools

cordless drill

3/16-in. drill bit

5/16-in. drill bit

1/2-in. wrench

3/8-in. wrench

9/16-in. wrench

1/2-in. socket wrench

screwdriver

pliers

rubber mallet

NOTE:

 Standard drill bits rapidly become dull when used on fiberglass. Ma

-

sonry bits are recommended. Use thread-locker on all bolts.

ASSEMBLY AND OPERATING INSTRUCTIONS:

Содержание Big Wheel RF2 Series









Отзывы: