Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 36

Страница: 36 / 62

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN

4-12

Preparation for Planter Transport

1. See “Safe Transport” on page 2-5 for safe operation

of tractor during transport.

2. Place the planter in the raised position with the wings

folded. See “Wing Fold” on page 4-7.

3. Do not attempt to transport the machine fully loaded.

NOTE:

Seed load must be at half capacity before

machine is transported.

4. Enable tractor safety lights. See “Warning and Safety

Lights” on page 2-6.

5. Do not exceed 20 mph (32 kph) when transporting

the planter.

Preparation for Planter Operation

1. Inspect implement for worn or damaged parts. See

“Implement Inspection” on page 7-7.

2. Be sure all mechanical, hydraulic, and electronic

connections are in place and free of making contact
with other moving parts.

3. Make sure cab hydraulic control configuration is

easily accessible and set to the preference of the
primary operator.

4. Make sure tractor is adequately ballasted for safe

operation. See the tractor operator’s manual for more
information on proper ballasting instructions.

DANGER

Avoid crushing. Failure to follow this information will
result in death or serious injury. Do not stand between
the tractor and implement when connecting or
disconnecting the implement.

5. Connect implement to tractor. See

“Implement-to-Tractor Connection” on page 4-4.

6. Raise bar stands (1) to highest point and install stay

pins (2).

ORM000123

Figure 4-21

7. Review the toolbar settings and features in

Chapter 5, “Operation and Field Settings”

. Make

any necessary adjustments.

1) Bar stand (2 used)

2) Stay pin (2 used)

Содержание 125-087-02-EN-OM































































Результаты поиска

Содержание 125-087-02-EN-OM

Отзывы:

Orthman 125-087-02-EN-OM, Руководство оператора, Страница: 36 / 62

Результаты поиска

Содержание 125-087-02-EN-OM

Отзывы: