OrthAlign KneeAlign 2 System Скачать руководство пользователя страница 9

15

KneeAlign

®

 2 System

 Surgical Technique Manual 

KneeAlign

®

 2 System

 Surgical Technique Manual

14

tIBIA

tIBIA

register Lateral malleolus

 •   

Palpate lateral malleolus and place cup of malleolar 

probe on its apex.

 •   

Press center button to register lateral malleolus.

TIP:   

Extend jig distally if necessary, by releasing ankle  

tube latch.

   

In event that leg is positioned at orientation outside of 

range of KneeAlign® 2 system, box at top center of screen 

will turn orange. Change position of leg until black ball  

is within square box and box has turned green.

TIP:   

A double beep will sound on registration.

   

Navigation unit must be maintained in steady position  

or red hand will flash on screen.

   

Ankle tube should be locked during registration.

Set resection plane

 •   

Retract malleolar probe to maximum anterior position.

 •   

Move distal end of tibial jig to obtain desired varus/

valgus and posterior slope angles and lock in place  

with side levers.

TIP:   

Malleolar probe may be adjusted to assist in setting  

posterior slope angle.

   

Do not use malleolar probe to set posterior slope angle  

if posterior slope lever is locked.

   

After locking levers, do not move jig relative to the tibia. 

Pushing or pulling locked bars of the jig may introduce  

errors in navigation accuracy.

   KneeAlign® 2 System does not display measurement  

values when oriented outside of its operating range. 

Change position of leg until black ball is within 

rectangular box and box has turned green.

register medial malleolus

 •    

Palpate medial malleolus and place cup of malleolar 

probe on its apex. Press center button on navigation  

unit to register medial malleolus.

TIP:   

A double beep will sound upon registration.

   

After registration, do not move base of jig relative to tibia.  

Keep fixation arm and v-rest in their attached positions.  

Pushing or pulling fixed base of jig may introduce errors  

in navigation accuracy.

 •   

Press center button on KneeAlign® 2 when this 

step is completed and remove midline probe  

by pulling straight up.

Step

Step

Step

4

5

6

V/V

Posterior 

Slope

P/S 

Lock

V/V 

Lock

Содержание KneeAlign 2 System













Отзывы: