Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 39 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Recommended sequence of operations

5.4.7. Cable test

These driving mechanisms allow the operation of going

from earthing switch closed to switch-disconnector

open, even when the cable compartment cover is

open. The switch-disconnector cannot therefore be

changed to closed position until this cover has been

put back.
The cable test can only be carried out in feeder

functions which include B/BM driving mechanisms

with this characteristic. Please check with

Ormazabal

Follow the steps in section "5.4.6. Earthing operation

from isolating position".

Leave the lever in the earthing switch access (yellow

area).

Open the bottom cover to access the cable

compartment.

With the lever in the earthing switch access, follow

the steps in section "5.4.3. Opening operation from

earthing position".

Carry out the cable test.

To return to earthing position, follow the steps in section

"5.4.6. Earthing operation from isolating position".

Close the bottom cover to access the cable

compartment.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды