Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 37 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Recommended sequence of operations

5.4.5. Opening operation from closed position

Move the actuating shaft access handle in the grey

zone to its bottom position.

2. Opening operation:

a. Manual operation

(B driving mechanisms). Insert

the lever in the switch access (grey area), move the

actuating arm to the end and turn anti-clockwise

90º.

b. Motorised operation

(BM driving mechanisms).

Activate the corresponding operation command.

Figure 5.14.

Lever turn process

Verify that the cubicle is in isolating position.

Figure 5.15.

Switch

disconnector open

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды