Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 33 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Recommended sequence of operations

5.3. Phase concordance check

[12]

Optionally, other comparison devices which comply with Standard IEC 62271-206 may be used.

[13]

See section "5.2. Voltage presence indicating relay" of these General Instructions.

Ormazabal

ekor

.spc

[12]

phase comparator should be used

for checking that the medium-voltage cables are correctly

connected to the feeder cubicles.

Firstly, connect the red cables of the

ekor

.spc unit to the

corresponding phase test points in the voltage indication

units

[13]

, and the black cable to the earth test point. This

operation must be repeated for all the phases: L1, L2 and L3

Figure 5.4.

Detail of

ekor

.spc

Figure 5.5.

Detail of

ekor

.spc

Comparison of balanced phases

Figure 5.6.

There is NO indication in the comparator.

Comparison of unbalanced phases

Figure 5.7.

There IS indication in the comparator

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды