Ormazabal velatia cgm.3 system Скачать руководство пользователя страница 25

Страница: 25 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Installation

4.8. Cable connection

[9]

In accordance with Figure 15-Interface 13 of Standard IEEE 386 – 2016 "600-900 A deadbreak interface 35 kV class"

[10]

It is advisable to use fully insulated connectors for voltages of 36 and 40.5 kV, according to HD 629.

The medium-voltage incoming and outgoing feeders are

linked to the transformer or, occasionally, other cubicles via

cables. These cables and the corresponding bushings in the

cgm

.3-huv system cubicles can be connected with simple

(plug-in) or reinforced (screw-in) connecting points, either

IEC type or IEEE-386 compliant

[9]

The cable compartment contains the connecting cable

bushings for the incoming and outgoing feeders, as well as

for the outgoing feeders to the transformer.

The size of the cable compartment allows the use of both

insulated and partially insulated cable connectors

[10]

Never touch live connectors, not even screened

connectors. Screening does not constitute protection

against direct contact.
When the equipment is in service and a reserve cubicle

is left with voltage in the top busbar and without the

cables in the bottom bushings, insulating plugs must

be placed in the bushings (EUROMOLD type) or the

disconnector earthed and locked in this position with

a padlock.

The

terminals recommended

for networks with U

= 36 kV

are detailed below.

Cable type

Rated current [A]

Manufacturer

Connector

36 kV

Connector type

Section [mm

]

Dry insulation

400

EUROMOLD*

Screened

M400LR

35-240

630

M400TB

35-240

630

M440TB

185-630

* Connectors recommended for

Ormazabal

’s

cgm

.3 system cubicles.

Table 4.6.

Recommended terminals

Apart from the list above, CENELEC terminals are also valid.

For other values, check with

Ormazabal

Moreover, the following maximum and minimum

dimensions for a standard cable connector when double

toroidal-cores are installed must be taken into account.

Max [mm]

Min [mm]

Table 4.7.

Max/min cable connector dimensions with double toroidal-core

current transformer

Figure 4.12.

Detail of max/min cable connector dimensions with double

toroidal-core current transformer

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды