Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 21 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Installation

4.5. Fixing to floor

[8]

See section 5. Operations Sequence

Before assembling the cubicles, the floor must be carefully

levelled to prevent any deformation which may make it

difficult to connect the cubicles to one another.

The cubicles can be fastened to the floor in two ways:

4.5.1. Fixing to floor on profile

If the floor of the facility is not sufficiently uniform, it is

advisable to install the medium-voltage cubicles on an

auxiliary profile, to make it easier to connect. This profile,

which can be supplied to order, must be anchored to the

floor using expansion bolts.

M10 x 25 bolt

65 x 65 x 4 mm profile

Anchoring bracket

Figure 4.6.

Positioning cubicles on profile

4.5.2. Fixing to floor by anchoring

If the floor of the facility is level enough, it is advisable to

install the medium-voltage cubicle anchored directly to the

floor.

The sequence for fixing the cubicles to the floor is as follows:

The cubicle's switch must be in earthing position

[8]

By default, the cubicles are supplied with the switch in

earthing position. Except in circuit-breaker functions,

which will be in isolating position.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды