Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 31 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Recommended sequence of operations

5. Recommended sequence of operations

Before carrying out any operation when voltage is

present, we recommend checking the SF

gas pressure

using the pressure gauge.

5.1. Checking the gas pressure

Each tank has a pressure gauge for checking the gas

pressure, which can easily be seen from outside the cubicle.

The pressure gauge scale is divided into different colours:

red, grey and green. For safe operation, the needle must be

in the green area of the relevant temperature band.

DO NOT REMOVE THE PLUG from the pressure gauge.

Figure 5.1.

Do not remove the pressure gauge cap

Figure 5.2.

Pressure gauge

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды