Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 15 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Installation

4. Installation

[4]

It is advisable to cut the cellophane at the rear of the cubicle or at the corner to avoid scratching the surface.

Tightening torques:
- M8: 20 Nm
- M10: 40 Nm

4.1. Unpacking the equipment

The

cgm

.3-huv system switchgear is supplied protected by

plastic packing as standard.

On receiving the equipment, check that the goods supplied

match the order and associated documentation. If this is

not the case, contact

Ormazabal

immediately.

The disassembly process for the equipment is as follows:

Use a blade, cutter or similar tool to cut the cellophane

the cubicle is wrapped in

[4]

Completely remove the cellophane.

Detach the white polystyrene corner pieces.

Unscrew the fixings between the base and the pallet.

Remove the pallet, handling the cubicle as indicated in

section 2.1.

Unpack the accessory box located at the rear or on top

of the cubicle.

Remove the self-adhesive protective plastic from the

cable compartment cover.

The self-adhesive plastic must be removed from the

cable compartment cover so that the equipment

enclosure's earth connection may have the proper

electrical continuity.

Dispose of any waste in an environmentally friendly

manner.

It is advisable to make a visual inspection of the equipment

to check whether it has suffered any damage in transit. If

damaged, contact

Ormazabal

immediately.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды