Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 12 / 76

IG-308-EN version 01; 03/06/2022

Handling and transport

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

2. Handling and transport

[3]

Position the rear of the cubicle facing the conductor, to avoid damaging the front.

Important: During transport, the switchgear must

be perfectly seated and fixed so that it cannot move

about and possibly damage the equipment.

2.1. Lifting equipment

The switchgear must always be kept upright, either directly

on the floor or on a pallet, depending on the type of

handling involved.

Handling should use one of the following methods:

Using a forklift truck or pallet truck

[3]

Figure 2.1.

Lifting a

cgm

.3-huv

modular cubicle using a forklift truck.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды