Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 10 / 76

IG-308-EN version 01; 03/06/2022

General description

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

1.5. Dimensions and weights

Figure 1.5.

Dimensions

cgm

Cubicle Width (a)

[mm]

Depth (f)

[mm]

Height (h)

[mm]

Bushings height (g)

[mm]

Cable fastening

height (i)

[mm]

Weight

[kg]

Gas output

418

860

1305

603

135.5

145

Downwards

through cable

trench

595

860

1305

256

235

378.5

860

1305

845.5

133

595

1152

1800

845.5

453

135

rbv*

595

860

2050

487

110

305

lv*

595

860

2050

487

110

325

418

860

1305

603

135.5

145

Upwards through

relief duct

(chimney)**

378.5

1152

1305

845.5

133

595

1152

1800

845.5

453

135

rbv*

595

1152

2050

487

110

325

lv*

595

1152

2050

487

110

345

* In the generator incoming cable compartment the gases output is directly upwards.
** Chimney depth: 292 mm.

Table 1.7.

Cubicle dimensions and weights

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды