Orlaco Camera EMOS Ethernet with Ex housing, Руководство по установке

Страница: 4 / 17

4 IM0973660 A 01
Open wires
1 = Orange/white = +Tx
2 = Green/white = +Rx
3 = Orange
= -Tx
4 = Green = -Rx
Overall shielding connected to connector housing.
Open wires
1 = Red = Power
2 = White = 0V
2. Pin connection
See figure 2.
3. Specifications
Camera EMOS Ethernet 30°/60°/90°
Description
Lens specified Hor. lens angle Ver. lens angle
EMOS 90° Ethernet 90° 68°
EMOS 60° Ethernet 60° 45°
EMOS 30° Ethernet 30° 22°
Sensor
Sensor element: High resolution 1/3” CMOS rolling shutter, 1280H x
960V.
Video image :60fps at 720p SDR, 45fps at 960p SDR image processing
and 56fps at 720p HDR, 43fps at 960p HDR image processing.
Protocols: RTP (MJPEG RFC2435 and h.264 RFC6184) over UDP, PTP
and gPTP, ISO17215-2014, IEEE1722 (AVB).
IP address : DHCPv4 or static IPv4 (IPv6 possible).
Latency : <100ms depending on hardware processing platform (50ms
demonstrated on Orlaco hardware).
Light sensitivity : responsitivity 5,5V/lux-sec, Low light feature (<0,1Lux).
High dynamic range: >115dB.
Compression : MJPEG, H.264 (High 10 intra profile encoding).
Interface : 100Mb/s (Fast Ethernet).
Image processing : Color and gamma correction, 3D noise correction,
edge enhancement, digital WDR, advanced contrast enhancement, auto
white-balance, auto exposure control, mirroring, flipping, photometric
and geometric lens distortion correction.
Electrical
Power input: 12/24V/DC. Below 7V: camera is non-functional. Above 33V
the overvoltage protection is activated. This overvoltage protection is
deactivated below 30V. Powercircuit is protected up to 80V/DC. Outputs
are Short Circuit Protected.
In all these above mentioned values; a tolerance of +/-10% is applied.
Power consumption : <2W.
Transient protection : Camera may be powered directly from 12V or
24V battery without additional electrical protection since camera has an
integrated circuit that protects the camera against over- and undervoltage,
spikes, ripples and loaddumps.
Cable: 6 wire: 2x twisted pair for data and 2 wires for power supply.
Min. cable bend radius : 50mm.
Mechanical
Camera housing: Anodised aluminium, black, UV resistant, light fastness
>8, corrosion proof according IEC 60068-2-52 salt mist, cyclic.
EX housing: Description; see page 7.
Filling: Camera is potted with automotive potting resin
Ingress protection : IP66 / IP67
Shock constancy : Shock and vibration resistant for usage on trucks,
cranes, fork-lifts, maritime applications, machinery.
Truck use: Withstand all fluids and materials used in and around trucks
like: ammonia solution 5%, ethanol 80-100%, isopropanol 5-10%, soapy
water (min. 50% soap per volume), alkaline degreasing compounds(used
in high pressure washing equipment).
Operating temperature : -40°C to +70°C
Storage temperature: -40°C to +125°C
Certification
Camera
Approvals : In compliance with all relevant EMC- and Automotive
directives.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Certificates available upon request.
Compliant with RoHS and REACH.
Ex housing
IECEx see page 11.
ATEX see page 14.
Installation Manual
Figure 2