Orion XTREME 400.4 Скачать руководство пользователя страница 3

INTRODUCTION

Thank you for your purchase of Orion's 4004 amplifier. Each Orion amplifier is designed to
be the leader in its class offering the most power, advanced features, and ease of use. Orion
amplifiers are designed as the best affordable high end car audio amplifier money can buy.
Listed below are the features of the new Orion 4004.

4004 -

50 Watts per channel, four-channel amplifier with dual built-in high-pass

and low-pass 12dB/octave crossover centered at 100Hz and INTELLi Bass. The 4004
is capable of 6, 5, 4, 3, or 2 channel operation with a maximum power capability
of 400 Watts into 4

W

stereo (front and rear channels bridged.)

The installation of all Orion amplifiers will determine the overall performance result.
Improper installation will not only limit the performance of your Orion system, but also
potentially compromise the reliability of the amplifier. To ensure proper sonic results and
component reliability, please refer to your authorized Orion dealer for installation assis-
tance or advice. If you decide to perform the installation yourself, be sure to read the entire
manual before beginning the installation.

What’s In The Box

(1) Amplifier

(1) Extra Fuses

(2) High Level Input Harness

(1) Allen Wrench 2.5mm

(1) Allen Wrench 3mm 

(4) #8 self-tapping black Phillips head pan head screws

(1) Amplifier installation and operation manual

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent hearing
loss. High power automotive sound systems can generate sound pressure levels in excess of
130dB. When playing your system at high levels, please use hearing protection and avoid
long term exposure.

2

©2004 Directed Electronics, Inc.

Содержание XTREME 400.4




















Отзывы: