background image

IMPORTANT INFORMATION

WARNING: The warnings, cautions and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It

must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.

When using the tool, basic safety precautions should always be followed to reduce the risk of

personal injury and damage to equipment.

Read and understand tool labels and operating instructions, safety precautions and warnings

in this manual before operating or maintaining this nailer.

Failure to follow warnings could result in

DEATH

or

SERIOUS INJURY

.

Most accidents that result from the operation and maintenance of nailers are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs and by observing appropriate
safety procedures.

Basic safety precautions are outlined in the "

SAFETY

" section of this manual and in the

sections which contain the operation and maintenance instructions. Hazards that must be

avoided to prevent bodily injury or tool damage are identified as

DANGERS

or

WARNINGS

on

the nailer and in this manual.
Never allow the nailer to be operated by children or individuals who have not reviewed this

manual.

OPERATE THE NAILER ACCORDING TO THIS MANUAL.

WARNING!

Always follow the tool manufacturer's safety and

maintenance instructions.

Always wear safety glasses with side shields when

operating or servicing tools.

Always disconnect the air supply from the tool and empty

the magazine when servicing tools.

SAVE THIS MANUAL

FOR FUTURE REFERENCE!

Содержание CN70















Отзывы: