3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
G1
G2
G3
G4
G9
G10
G11
G12
G5
G6
G7
G8
G1~G12
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DB-
5 BI_DD+
6 BI_DD-
7 BI_DC-
8 BI_DC+
6
5
7
3
2
1
8
4
Power
24-110VDC
V-
N.C.
V+
N.C.
Power
Failure
Bypass
Power
Failure
Bypass
TGRS-T120-M12X-BP2-WV
LNK/ACT Speed
Reset
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
LNK/ACT
Speed
PWR
Status
R.M.
Ring
Fault
Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ORing's Transporter
series managed Router switches are designed for
T M
industrial applications such as rolling stock, vehicle, and railway. The
TGRS-
T120-M12X-BP2-WV
, which is compliant with the EN50155 standard, is a
m a n a g e d
G i g a b i t
R e d u n d a n t
R i n g
E t h e r n e t
s w i t c h
w i t h
12x10/100/1000Base-T(X) ports which is specifically designed for the
toughest and fully compliant with EN50155 requirement. The switch support
IEC 61375-2-5 TTDP
IEC 61375-2-3
(Train Topology Discovery Protocol) and
TRDP
(Train Real-Time Data Protocol) for railway application, improving the
operational efficiency and minimize configuration errors. It is specifically
designed for the toughest industrial environments.
TGRS-T120-M12X-BP2-
WV
EN50155 Ethernet switch uses M12 connectors to ensure tight, robust
connections, and guarantee reliable operation against environmental
disturbances, such as vibration and shock.
TGRS-T120-M12X-BP2-WV
EN50155 provides a wide power input range from 24 to 110VDC.
TGRS-T120-
M12X-BP2-WV
includes 2 sets of bypass ports that protect the network from
failures and Network maintenance by ensuring network integrity during power
loss. And support wide operating temperature from -25 C to 70 C.
o
o
TGRS-
T120-M12X-BP2-WV
can also be managed centralized and convenient by
Open-Vision, as well as the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the router switch is one of the most reliable choice
for highly-managed and railway application.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1:
Hold the
evice upright against the wall
d
Step 2:
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3:
Slide the
evice downwards and tighten the four screws for added stability.
d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGRS-T120-M12X-BP2-WV
Pictures
Number
1
Panel Layouts
Front View
1. Power status LED
2. System status LED
3. R.M. status LED
4. Ring status LED
5. Fault LED
6. Reset button
7. Ethernet LAN ports
8. Ethernet WAN ports with bypass
9. Link/ACT LED for Gigabit ports
10. Speed LED for Gigabit ports
11. Console port
12. Relay output
13. Power connector
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports one set of power supply and uses the M12 A-coded
5-pin male connector on the front panel for power input.
Step 1:
Insert a power cable to the power connector on the device.
Step 2:
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Relay output port pinouts
Relay
N.C.
3A@24VDC
Network Connection
The switch has twenty 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
TGRS-T120-M12X-BP2-WV
1907-200-XX
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
8-pin female M12
X-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
X-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
X-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG
1
11
12
13
4 5
6
2 3
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
N.C.
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Dimension
Unit =mm (Tolerance ±0.5mm)
TGRS-T120-M12X-BP2-WV
EN50155 managed router switch
3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
G1
G2
G3
G4
G9
G10
G11
G12
G5
G6
G7
G8
G1~G12
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DB-
5 BI_DD+
6 BI_DD-
7 BI_DC-
8 BI_DC+
6
5
7
3
2
1
8
4
Power
24-110VDC
V-
N.C.
V+
N.C.
Power
Failure
Bypass
Power
Failure
Bypass
TGRS-T120-M12X-BP2-WV
LNK/ACT Speed
Reset
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
LNK/ACT
Speed
PWR
Status
R.M.
Ring
Fault
9
10
7
8
V-
N.C.
V+
N.C.
6
5
7
3
2
1
8
4
10/100/1000Base-T(X)
M12 X-coding
Pin No.
Pin Definition
#1
BI_DA+
#2
BI_DA-
#3
BI_DB+
#4
BI_DB-
#5
BI_DD+
#6
BI_DD-
#7
BI_DC-
#8
BI_DC+
