Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
1907-2-29-RGPS9084GPP-1.0
The
is managed PoE Ethernet switch with eight Gigabit
P.S.E. ports and four Gigabit SFP ports. The P.S.E ports can transmit
electrical power up to 30 watts per port (240watts in total between -40 ~
60 C and 120watts in total between 60 ~ 75 C) along with data to remote
devices over standard twisted-pair cables. The switch supports several
Ethernet redundancy technologies such as O-Ring (recovery time<30ms
over 250units of connection) and O-Chain topologies, as well as MSTP
protocol (RSTP/STP compatible) to protect mission-critical applications
from network interruptions or temporary malfunctions with fast recovery
technology. With a wide operating temperature from -40 C to 75 C, the
device can be managed centrally via ORing’s proprietary Open-Vision
management utility as well as via Web-based interfaces, Telnet, and
console (CLI).
RGPS-9084GP-P
o
o
o
o
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Safety & Warnings
Dimension
Panel Layouts
1. Reset button
2. Console port
3. Power indicator
4. Ring status LED
5. RM status LED
6. LAN ports
Front View
Rear View
Network Connection
Package Contents
Contents
QIG
CD
Screw (M4 X6)
Power cord
Rack-mounted
kit (L&R)
Number
X 1
X 1
X 6
X 1
X 1
RGPS-9084GP
-P
Pictures
M A N A G E D
Rack-Mount
GIGABIT
SWITCH
PoE
X 1
7. LNK/ACT indicator for Ethernet LAN ports
8. Speed indicator for Ethernet LAN ports
9. PoE indicator
10. SFP port
11. LNK/ACT LED for SFP ports
1
2
1. Power switch
2. AC power input (100V~240V
/ 50~60Hz)
The series have standard Ethernet ports. According to the link type, the switch uses CAT 3, 4,
5,5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or
hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
For pin assignments for different types of cables, please refer to the following
tables.
1000Base-T P.S.E. RJ-45 port
Pin Number
Assignment
#1
BI_DA+ with PoE Power input +
#2
BI_DA- with PoE Power input +
#3
BI_DB+ with PoE Power input -
#4
BI_DC+
#5
BI_DC-
#6
BI_DB- with PoE Power input -
#7
BI_DD+
#8
BI_DD-
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Installation
Rack-mounting
Step 1:
Step 2:
Install left and right front mounting brackets to the switch using three screws on each side.
With front brackets orientated in front of the rack, fasten the brackets to the rack using two
more screws.
RGPS-9084GP-P
RGPS-9084GP-P
Managed Gigabit PoE Ethernet Switch
1000X
PWR
Ring
R.M.
44.00
443.70
58.00
42.70
26.70 24.00
24.00
30.20
3.90
R3.50
19.00
3.70
185.25
15.90
6.50
230.00
G1
G3
G5
G7
AC100-240V
50-60HZ
380.00
49.0
3.0
G9
G10
G11
G12
G1
G3
G5
G7
RGPS-9084GP-P
Full Gigabit Ethernet PoE Switch
Reset
PoE
115200, 8, N, 1
Console
LINK / ACT
2.65
PWR Ring
R.M.
1000X
1000X
PWR
Ring
R.M.
G1
G3
G5
G7
G9
G10
G11
G12
G1
G3
G5
G7
RGPS-9084GP-P
Full Gigabit Ethernet PoE Switch
Reset
PoE
115200, 8, N, 1
Console
LINK / ACT
PWR Ring
R.M.
1000X
2
3 4 5 6
7
1
8
9
10 11
AC 100-240V
50-60 HZ
10/100Base-T(X) P.S.E RJ-45 Port
Pin Number
Assignments
1
TD+ with PoE Power input +
2
TD- with PoE Power input +
3
RD+ with PoE Power input -
4
Not used
5
Not used
6
RD- with PoE Power input -
7
Not used
8
Not used
Note:
and
signs represent the polarity of the wires that make up each wire pair.
“+”
“-”
Console Cable
X 1
10/100Base-T(X) MDI/MDI-X Pin Assignments:
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
1000Base-T MDI/MDI-X Pin Assignments
Pin Number
MDI port
MDI-X port
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
