Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
ITGMC-111GP+
1907-2-29-ITG-1.0
The
is a cost-effective solution for interface conversion
between 1G/10GBase-T and 1G/10GBase-X SFP+ socket. It allows you to
extend communication distance of Gigabit copper port with optical fiber. The
supports MDI/MDIX auto detection, so you don’t need to use
crossover wires. With a wide operating temperature range from -20~60 C
and a wide voltage range from dual 12~48 VDC power inputs, the
is suitable for harsh operating environments. Therefore, the
is one of the most reliable media converters in harsh industrial
environments.
ITGMC-111GP+
ITGMC-111GP+
ITGMC-
111GP+
ITGMC-
111GP+
o
Package Contents
Installation
The series is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the d
should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
in-rail
Safety & Warnings
Dimension (Unit: mm)
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
DIN-rail Installation
Media
C o nv ert e r
Media
C o nv ert e r
I N D U S T R I A L
ITGMC-111GP+
Panel Layouts
Front Panel
1. Power LED
2. Relay LED
3. DIP switch for relay
4. LNK/ACT LED for 10G copper port
5. 10G port
6. Speed LED for 10G SFP port
7. LNK/ACT LED for 10G SFP port
8. 10G SFP port
Top Panel
2
1. Terminal block
2. Grounding
Real Panel
1. Wall-mount screw holes
2. Din-rail screw holes
1
3
Industrial Gigabit Media Converter
Contents
ITGMC-111GP+
Pictures
Number
X 1
QIG
X 1
DIN-rail kit
X 1
Wall-Mount Kit
X 2
ITGMC-111GP+
2
4
5
6
7
8
1
1
1
2
Wall-mount
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of
screws are required, as shown below.
Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
eight
Network Connection
The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the AP uses
CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
