Q I G
Quick Installation Guide
PRINTED ON RECYCLED PAPER
Q
uick
I
nstallation
G
uide
Q I G
Wiring
This device supports dual redundant power supplies, Power Supply
1 (PWR1) and Power Supply 2 (PWR2). The connectors for PWR1
and PWR2 are located on the terminal block.
STEP 1:
Insert the negative/positive DC wires into the V-/V+
terminals, respectively.
STEP 2:
To keep the DC wires from pulling loose, use a small flat-
blade screwdriver to tighten the wire-clamp screws on the front of
the terminal block connector.
Power inputs
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground screws to the grounding surface prior to
connecting devices.
Grounding
Configurations
After installing the device and connecting cables, the green power LED
should turn on. Please refer to the following tablet for LED indication.
Version 1.5
PWR-1
PWR-2
V1-
V1+
V2-
V2+
Network Connection
The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the
AP uses CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs,
servers, switches, routers, or hubs).
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
For pin assignments for different types of cables, please refer to the following tables.
Specifications
Enclosure
IP-30
Dimension (W x D x H)
45(W)x80.6(D)x95(H) mm (1.77 x 3.17 x 3.74 inch.)
Weight (g)
Environmental
-40 to 85 C (-40 to 185 F)
o
o
Storage Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
CE EMC (EN 55024, EN 55032), FCC Part 15B
EMC
EN 55024 (IEC/EN61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT),
IEC/EN 61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8(PFMIF)
IEC/EN 61000-4-11 (DIP))
EMS
IEC60068-2-27
Shock
IEC60068-2-31
IEC60068-2-6
Vibration
Free Fall
Warranty
3 years
UL61010-1/-2-201, EN60950-1
Safety
-10 to 60 C (14 to 140 F)
o
o
Operating Temperature
372g
10/100 Base-T(X) RJ-45 Pin Assignments
Pin Number
Assignment
1
TD+
2
TD-
3
RD+
4
Not used
5
Not used
6
RD-
7
Not used
8
Not used
10/100 Base-T MDI/MDI-X Pin Assignments
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
Cable Types and Specifications.
I N D U S T R I A L
M2M
Gateway
Industrial Cellular M2M Gateway
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Website: www.oringnet.com
E-mail: [email protected]
IMG-4312(+)-MN Series
IMG-4312(+)-MN Series
LED
Color
Status
Description
PW1
Green
On
DC power module 1 activated
PW2
Green
On
DC power module 2 activated
PoE
Green
On
PoE enabled
10/100Base-T(X) RJ45 Port
LNK/ACT
Green
On
Port is linked and transmitting data
Serial Port
Rx
Red
On
Port is receiving data
Tx
Green
On
Port is transmitting data
WiFi Connection
LNK/ACT
Green
On
Wireless network is linked
WAN Connection
LNK/ACT
Green
On
Power is on and functioning normally
Frequency Band
Transmission Rate
Encryption Security
WEP: (64-bit, 128-bit key supported)
WPA/WPA2: (WEP and AES encryption) 802.11i
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Transmit Power
Receiver Senstivity
ORing Device Server Model
10/100Base-T(X) Ports in Auto
MDI/MDIX
2
Physical Ports
Technology
Modulation
Wifi Interface
Antenna and Connector
IMG-4312+-MN
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM
IEEE802.11n: BPSK, QPSK, 16-QAM, 64-QAM
America / FCC : 2.412~2.462 GHz (11 channels)
Europe CE / ETSI : 2.412~2.472 GHz (13 channel)
802.11b: -90dBm±2.0dB @ 11Mbps
802.11g: -72dBm±2.0dB @ 54Mbps
802.11n(2.4G@40MHz, MCS7): -68dBm 2dBm
±
801.11b: 1/ 2/ 5.5/ 11 Mbps
801.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
802.11n
: UP to 150 Mbps
(40MHz)
802.11b: 19dBm ±1.5 dBm
802.11g: 17dBm ±1.5 dBm
802.11n(2.4G@20MHz): 16dBm 1.5dBm
±
802.11n(2.4G@40MHz): 14dBm 1.5dBm
±
1 x RP-SMA Female
PoE P.D. port
P.O.E.Present at ETH1
Power Device (IEEE 802.3af ):
IEEE 802.3af compliant input interface
Over load & short circuit protection
Isolation Voltage: 1000 VDC min.
Isolation Resistance: 10 ohms min
8
IMG-4312-MN
Sim Card Slot
1
Cellular Interface
Antenna Connector
Cellular Standard
Band Option
LTE Cat-M1/Cat-NB1 :
LTE FDD:
B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28
LTE Cat-M1 :
LTE TDD :B39
LTE Cat-M1/Cat-NB1
Power
Redundant Input power
Dual DC inputs. 12~48VDC on 4 pin terminal block
Power Consumption(Typ.)
3.5 Watts
Overload current protection
Present
Reverse polarity protection
Present on terminal block
Physical Characteristic
2 x SMA Female
Serial Port
Connector
DB9 x1
Operation Mode
RS-232/422/485
Serial Baud Rate
110 bps to 115.2 Kbps
Data Bits
7, 8
Parity
odd, even, none, mark, space
Stop Bits
1, 1.5, 2
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
Flow Control
XON/XOFF, RTS/CTS, DTR/DSR
Network Protocol
Protocol
ICMP, IP, TCP, UDP, DHCP, BOOTP, SSH, DNS, SNMP V1/ V2c, HTTPS, SMTP, DDNS, PPPoE
Download/Upload Rate
LTE Cat-M1:300 / 375 Kbps
LTE Cat-NB1: 32 / 70 Kbps
-
EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Part 15 class A
EMI
MTBF
671546.9934 hrs
