PWR-1
PWR-2
V2+ V2- V1+ V1-
1A@24V
Q I G
Quick Installation Guide
Q
uick
I
nstallation
G
uide
Version 2.2
Q I G
Cable Types and Specifications:
For pin assignments for different types of cables, please refer to the following
tables.
10/100 Base-T(X) MDI/MDI-X
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
Note: “+” and “-” signs represent the polarity of the wires that make up each
wire pair.
10/100 Base-T(X) RJ-45
Pin Number
Assignment
1
TD+
2
TD-
3
RD+
4
Not used
5
Not used
6
RD-
7
Not used
8
Not used
Resetting
To reboot the switch, press the
button for 2-3 seconds.
Reset
To restore the switch configurations back to the factory defaults, press the
button for 5 seconds.
Reset
Wiring
The device has two sets of power inputs, power input 1
and power input 2. Follow the steps below to wire redundant
power
Power inputs
The two relay contacts on the terminal block allow you to form fail close circuits.
The relay contacts will respond to user-configured events according to the wiring.
Relay contact
Grounding and wire routing help limit the effects of noise due to electromagnetic
interference (EMI). Run the ground connection from the ground screws to the grounding
surface prior to connecting devices.
Grounding
Configurations
After installing the switch, the green power LED should turn on. Please refer to the
following tablet for LED indication.
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP address is
192.168.10.1
2. Log in with default user name and password
(both are
).
After logging in, you should
admin
see the following screen. For more information
on
configurations, please refer to the user
manual. For information on operating the switch
using ORing’s Open-Vision management utility,
please go to ORing website.
Follow the steps to set up the card:
Specifications
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
STEP 1:
Insert the negative/positive wires into the V-/V+ terminals, respectively.
STEP 2:
To keep the wires from pulling loose, use a small flat-blade screwdriver
to tighten the wire-clamp screws on the front of the connector.
ORing Switch Model
IES-2050A
10/100 Base-T(X) Ports in RJ45 Auto
MDI/MDIX
Physical Ports
5
Technology
Ethernet Standards
IEEE 802.3 for 10Base-TX
IEEE 802.3u for 100Base-TX
IEEE 802.3x for Flow control
IEEE 802.1D for STP (Spanning Tree Protocol)
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Fault Contact
Relay
Relay output to carry capacity of 1A at 24 VDC
Power
Redundant Input power
Power consumption(Typ.)
Dual DC inputs, 12~48VDC on 6-pin terminal block
Overload current protection
Reverse polarity protection
Present
Present on terminal block
Physical Characteristic
Enclosure
IP-30
Metal (non UL certified)
Dimension (W x D x H)
26.1 mm (W) x 95 mm (D) x 144.3(H) mm (1.03 x 3.74 x 5.68 inch.)
Weight (g)
Environmental
-40 to 85 C (-40 to 185 F)
o
o
Storage Temperature
MAC Table
1K
≤4Watts, 12VDC/0.29A (3W), 24VDC/0.14A (3W), 48VDC/0.08A (4W)
* Supplied by SELV source evaluated by UL 61010-1 or 61010-2-201 power supply only.
* Fourni par la source SELV évaluée uniquement par l'alimentation UL 61010-1 or 61010-2-201.
395 g
Priority Queues
4
Processing
Store-and-Forward
Switch Properties
Switching latency: 8.94 µs
Switching bandwidth: 1Gbps
Throughput (packet per second): 76.19Mpps@64Bytes packet
VLAN: Port based
Security Features
Enable/disable ports,
VLAN to segregate and secure network traffic
Software Features
STP/RSTP (IEEE 802.1D/w)
Redundant Ring (O-Ring) with recovery time less than 10ms over 250units
DHCP Client
Port base VLAN
LLDP (Link Layer Discovery Protocol)
Port configuration, status, statistics, monitoring, security
SNMP v1/v2c /v3 and private MIB support
Network Redundancy
O-Ring
O-Chain
Fast recovery
RSTP/STP
-40 to 75 C (-40 to 167 F)
o
o
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
CE EMC (EN 55024, EN 55032, EN 61000-6-2, EN 61000-6-4), FCC Part 15 B
EMC
EN 55024 (IEC/EN 61000-4-2 (ESD: Contact 4KV, Air 8KV), IEC/EN 61000-4-3 (RS: 3V),
IEC/EN 61000-4-4 (EFT Power 0.5KV, Signal 0.5KV), IEC/EN 61000-4-5 (Surge: Power 0.5KV, RJ45 0.5KV),
IEC/EN 61000-4-6 (CS: 3V), IEC/EN 61000-4-8(PFMF), IEC/EN 61000-4-11 (DIP))
EN 61000-6-2 (IEC/EN 61000-4-2 (ESD: Contact 4KV, Air 8KV), IEC/EN 61000-4-3 (RS: 10V),
IEC/EN 61000-4-4 (EFT Power 2KV, Signal 1KV), IEC/EN 61000-4-5 (Surge: Power 0.5KV),
IEC/EN 61000-4-6 (CS: 10V), IEC/EN 61000-4-8(PFMF), IEC/EN 61000-4-11 (DIP))
EMS
IEC60068-2-27
Shock
IEC60068-2-31
IEC60068-2-6
Vibration
EN 60950-1 (LVD)
Safety
Free Fall
MTBF
1796601.9604 hrs
PRINTED ON RECYCLED PAPER
SWITCH
I N D U S T R I A L
Industrial Lite-Managed Switch
DIP-Switch setting
P.F.
Trigger alert when power fails (
On
: Enable,
Off
: Disable function)
R.E.
Enable/Disable O-Ring function (
On
: Enable,
Off
: Disable)
R.M.
Enable/Disable Ring Master Mode (
On
: Enable,
Off
: Disable)
R.S.
Select O-Ring redundant port (
On
: ring port set to port-5 and port-6,
Off
: ring port set to port-1 and port-2)
LED
Color
Status
Description
P1
Green
On
Power module 1 is activated
P2
Green
On
Power module 2 is activated
R.M
Green
On
System running in Ring Master mode
Ring
Green
On
System running in Ring mode
Blinking
Ring structure is broken (i.e. part of the
ring is disconnected)
Fault
Amber
On
Faulty relay (power failure or port
malfunctioning)
10/100Base-T(X) Fast Ethernet ports
LNK
/ACT
Green
On
Links are connected
Blinking
Transmitting data
Duplex/
Collision
Amber
On
Full-duplex mode
Off
Half-duplex mode
Blinking
Half-duplex and collision occurred
IES-2050A
IES-2050A
Packet buffer
1Mbits
EN 55032, EN 61000-6-4, CISPR32, EN 61000-3-2, EN 61000-3-3, VCCI class A, FCC Part 15 B class A
EMI
Warranty
5 years
ORing Industrial Networking Corp.
Copyright© 2015 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Address 3F
No 542 2 Zhongzheng Rd
Xindian Dist
New
:
.,
.
- ,
.,
.,
Taipei City 23148 Taiwan
,
Website: www.oringnet.com
E-mail: [email protected]
Contact for maintenance and repair service:
！
Warning [AVERTISSEMENT]
Take into consideration the following guidelines before wiring the device
[Tenez compte des directrices suivantes avant de câbler l’appareil.]
1. Terminal block is mating with Plug and suitable for 12-24AWG.
Torque value 4.5 lb-in.
[Le bornier est compatible avec les connecteurs et convient pour 12-24AWG.
Valeur de couple 4,5 lb-in.]
2. The temperature rating of the input connection cable should higher than 105°C
[La température de service nominale du câble d’entrée doit être supérieure à 105 °C]
* Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the
device and label.
* Utilisation en intérieur et degré de pollution II, il faut l'essuyer avec un chiffon sec pour
nettoyer l'appareil et son étiquette.
* Do not block air ventilation holes.
* Ne bouchez pas les orifices de ventilation.
* If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.”
* Si l’appareil est utilise d’une maniere non specifiee par le fabricant, la protection qu’il
apporte peut se voir diminuee.”
* Shall be mounted in the Industrial Control Panel and ambient temperature is not exceed
75 degree C
* doit être monté dans le panneau de commande industriel et la température ambiante ne
doit pas dépasser 75 degrés C
！
Up to 2000m
Operating Altitude
