Quick Installation Guide
Version 1.2
Q
uick
I
nstallation
G
uide
PRINTED ON RECYCLED PAPER
Q I G
1907-2XX
Installation
DIN-rail
Step 1 :
Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2 :
Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into
the rail firmly.
Dimension
Unit =mm (Tolerance ±0.5mm)
Panel Layouts
Front Panel
1. Power status indicators
2. LAN connection status
indicators
3. Serial signal reception
status indicator
4. Serial signal transmission
status indicator
5. Dip switch button
6. Ethernet port
7. Serial port
1. Din-rail screw holes
2. Wall-mount screw holes
Network Connection
The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the AP uses
CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
IDS-312L
Introduction
The
is an
one
two
IDS-312L
innovative secure
port RS-232/422/485 to
port
LAN device server with standard features of device server, such like
s
TCP/IP interface and versatile operation modes: Virtual Com, Serial Tunnel,
TCP Server, TCP Client, and UDP. In addition, the Windows untility, DS-
Tool, could configure multiple devices and set up the mappings of Virtual
Com. On the other hand,
can simultaneously transfer data up to 5
it
redundant host PCs to a
id Ethernet connection breakdown or any host
vo
PC fails. Further,
feature
HTTPS, SSH, and SSL encryption to
IDS-312L
s
assure the security of critical data transmission.
supports RS-
The device
232/422/485 and provides dual redundant power inputs, 12~48 VDC, on
terminal block to guarantee a non-stop operation. With wide operating
temperature, -10~70 C, and rugged IP-30 housing design, t
could
o
he device
operate in the harsh industrial environment. Therefore,
the
IDS-312L
is
best solution to the high demand of secure serial to Ethernet critical data
communication.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents
CD
IDS-312L
Pictures
Number
X 1
QIG
X 1
X 1
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure the
operating ambient temperature is compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation of the
equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
Safety & Warnings
DIN-rail kit
X 1
Wall-Mount Kit
X 2
Rear Panel
Top Panel
1. Terminal block
2. Reset button
Wall-mount
Step 1:
Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of
screws are required, as shown below.
eight
Step 2:
Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Step 3:
Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
4-pin terminal block
X 1
Dust cover
X 2
Industrial Device Server
Device
Server
IDS-312L
1
2
5
6
7
2
3
4
1
2
2
1
2
Pull
Hi
/Low
Term.
Res.
Pull
Hi
/Low
Term.
Res.
Pull
Hi
/Low
Term.
Res.
IDS-312L
The product is open type, intended to be installed in and industrial control panel or an
enclosure.
* Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the device and
label.
* Utilisation en intérieur et degré de pollution II, il faut l'essuyer avec un chiffon sec pour nettoyer
l'appareil et son étiquette.
* Do not block air ventilation holes.
* Ne bouchez pas les orifices de ventilation.
* If the equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired.”
* Si l’appareil est utilise d’une maniere non specifiee par le fabricant, la protection qu’il apporte
peut se voir diminuee.”
* Shall be mounted in the Industrial Control Panel and ambient temperature is not exceed
70 degree C
* doit être monté dans le panneau de commande industriel et la température ambiante ne doit pas
dépasser 70 degrés C
！
