background image

11

 

„

Alarm reset

When the power is cycled, the alarm will be reset. Before resetting an alarm, 
always remove the cause of the alarm and ensure safety.
The overheat alarm can be reset by the AWO input if the circuit temperature 
of the driver goes down 75 °C (167 °F) and under. Be sure to check the circuit 
temperature went down 75 °C (167 °F) and under before resetting the alarm 
by turning the AWO input from OFF to ON.

Overheat alarm

Overheat status

*1

*2

*1 85 °C (185 °F) or more
*2 75 °C (167 °F) or more

2 ms or less

0.2 s or less

0 s or more

0.1 s or less

OFF

ON

OFF

ON

AWO input

ALM output

Non-excitation

Excitation

Motor excitation

Maintenance/inspection

 

„

Inspection

It is recommended that periodic inspections are conducted for the items 
listed below after each operation of the motor. If an abnormal condition is 
noted, discontinue any use and contact your nearest Oriental Motor sales 
office.

During inspection

 

y

Check if the mounting screws or the connecting parts of connectors for the 
driver are loose.

 

y

Check if dust and others attach on the driver.

 

y

Check if the driver has unusual smells or appearance defects.

The driver uses semiconductor elements, so be extremely careful 
when handling them. Static electricity may damage the driver. 

 

„

Warranty

Check on the Oriental Motor Website or General Catalog for the product 
warranty.

 

„

Disposal

Dispose the product correctly in accordance with laws and regulations, or 
instructions of local governments.

General specifications

Operation 
environment

Ambient 
temperature

0 to +50 °C (+32 to +122 °F) (non-freezing)

Humidity

85% or less (non-condensing)

Altitude

Up to 1000 m (3300 ft.) above sea level

Surrounding 
atmosphere

No corrosive gas, dust, water or oil

Storage 
environment, 
Shipping 
environment

Ambient 
temperature

−25 to +70 °C (−13 to +158 °F)  
(non-freezing)

Humidity

85% or less (non-condensing)

Altitude

Up to 3000 m (10000 ft.) above sea level

Surrounding 
atmosphere

No corrosive gas, dust, water or oil

Regulations and standards

 

„

CE Marking

 

z

Low Voltage Directive

Although this product is exempt from the Low Voltage Directive since 
the input power supply voltage is 24 VDC, perform the installation and 
connection as follows.

 

y

This product is designed and manufactured to be incorporated in 
equipment. Be sure to install the product in an enclosure.

 

y

For the driver power supply, use a DC power supply with reinforced 
insulation on its primary and secondary sides.

 

z

EMC Directive

This product is conducted EMC testing under the conditions specified 
in "Example of motor and driver installation and wiring" on p.9. The 
conformance of your mechanical equipment with the EMC Directive will vary 
depending on such factors as the configuration, wiring, and layout for other 
control system devices and electrical parts used with this product. It therefore 
must be verified through conducting EMC measures in a state where all parts 
including this product have been installed in the equipment.

Applicable Standards

EMI

EN 55011 group 1 class A, EN 61000-6-4

EMS

EN 61000-6-2

This equipment is not intended for use in residential 
environments nor for use on a low-voltage public network 
supplied in residential premises, and it may not provide 
adequate protection to radio reception interference in 
such environments.

 

„

Republic of Korea, Radio Waves Act

This product is affixed the KC Mark under the Republic of Korea, Radio Waves 
Act.

 

„

RoHS Directive

The products do not contain the substances exceeding the restriction values 
of RoHS Directive (2011/65/EU).

Accessories

 

„

Connection cable set

For the connection cable set, a set of three cables for the power supply, 
motor, and input/output signals is provided.

Model

Length [m (ft.)]

Conductor

LCS04SD5

0.6 (2)

AWG22 

 (0.3 mm

2

)

 

„

Connection cable (for signal)

This is a shielded twisted pair cable for the driver control I/O signals (12 pins) 
that has good noise immunity. The ground wires useful to grounding are 
provided at both ends of the cable.

Model

Length [m (ft.)]

Conductor

CC12D005-2

0.5 (1.6)

AWG24 

 (0.2 mm

2

)

CC12D010-2

1 (3.3)

CC12D015-2

1.5 (4.9)

CC12D020-2

2 (6.6)

Содержание CVD512B*-KSC series

















Отзывы: