Orientalmotor BXII Series Скачать руководство пользователя страница 3

Страница: 3 / 52

Introduction

−3−

2 Introduction

Only qualified personnel should work with the product.

Use the product correctly after thoroughly reading the section "1 Safety precautions" on page.2.

The product described in this manual has been designed and manufactured to be incorporated in general industrial

equipment. Do not use for any other purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused

through failure to observe this warning.

Overview of the product

The

OPX-2A

is a data setter that lets you set operation data and parameters, perform monitoring, etc.

Use the

OPX-2A

properly and safely after thoroughly reading the "

Ⅱ

Series USER MANUAL" and understanding

the basic operating procedures and other details.

Features of OPX-2A

The

OPX-2A

can be used to save data in addition to setting of operation data and parameters.

There are four destinations (data banks) to save data.

OPX-2A

Data bank 1

Data bank 0

Data bank 2

Data bank 3

Driver

Set operation data and parameters.

Up to 4 sets of operation data and

parameters can be saved.

Copy any one of the four

sets to the driver.

The

OPX-2A

can be used for the following purposes:

•

Operation data and parameters of the driver can be set.

•

The operating status of the motor can be monitored.

•

Operation data and parameters set in the driver can be saved to the

OPX-2A

•

Operation data and parameters saved in the

OPX-2A

can be copied to other drivers.

Specifications

Connection

Mini DIN, 8 pins

External dimensions 96 (W)×72 (H)×21.5 (D) mm

[3.78 (W)×2.83 (H)×0.85 (D) in.]

Cable length

5 m (16.4 ft.)

Mass

0.25 kg (8.8 oz)

RoHS Directive

The products do not contain the substances exceeding the restriction values of RoHS Directive (2011/65/EU).

Содержание BXII Series





















































Результаты поиска

Содержание BXII Series

Отзывы:

Orientalmotor BXII Series, Руководство по эксплуатации, Страница: 3 / 52

Результаты поиска

Содержание BXII Series

Отзывы: