manualshive.com logo in svg

Orientalmotor BXII Series, Руководство по эксплуатации, Страница: 2 / 52

Поделиться
Скачать
Orientalmotor BXII Series Скачать руководство пользователя страница 2

Safety precautions

−2−

1  Safety precautions

The precautions described below are intended to prevent danger or injury to the user and other personnel through safe, 

correct use of the product. Use the product only after carefully reading and fully understanding these instructions.

Also read the "Safety precautions" sections in the USER MANUAL that came with the product you are combining 

with the 

OPX-2A

.

Handling the product without observing the instructions that accompany a "Warning" 

symbol may result in serious injury or death.
Handling the product without observing the instructions that accompany a "Caution" 

symbol may result in injury or property damage.

Note

The items under this heading contain important handling instructions that the user should 

observe to ensure safe use of the product.

General

 

•

Do not use the product in explosive or corrosive environments, in the presence of flammable gases, locations 

subjected to splashing water, or near combustibles. Doing so may result in fire, electric shock or injury.

 

•

Assign qualified personnel the task of installing, wiring, operating/controlling, inspecting and troubleshooting the 

product. Failure to do so may result in fire, electric shock or injury.

 

•

When the driver’s protective function is triggered, first remove the cause and then clear the protective function. 

Continuing the operation without removing the cause of the problem may cause malfunction of the motor and 

driver, leading to injury or damage to equipment.

Repair, disassembly and modification

 

•

Do not disassemble or modify the data setter. This may cause electric shock or injury. Refer all such internal 

inspections and repairs to the branch or sales office from which you purchased the product.

General

 

•

Do not use the motor, gearhead and driver in conditions exceeding the specifications. Doing so may result in 

electric shock, injury or damage to equipment.

Operation

 

•

Provide an emergency stop device or emergency stop circuit so that the entire equipment will operate safely in the 

event of a system failure or malfunction. Failure to do so may result in injury.

Disposal

 

•

Dispose the product correctly in accordance with laws and regulations, or instructions of local governments.

Содержание BXII Series





















































Отзывы:

Нет отзывов