manualshive.com logo in svg

Oriental motor NETC01-M2, Руководство пользователя

Поделиться
Скачать
Oriental motor NETC01-M2 Скачать руководство пользователя страница 5

Introduction

5

 

„

System configuration

Termination

resistor *3

Termination

resistor: ON *2

Termination

resistor *1

MECHATROLINK-II

communication

MECHATROLINK-II

communication

compatible products

MECHATROLINK-II

communication

compatible products

NETC01-M2

RS-485 communication

compatible products

Master station

RS-485

communication

*1 The master device may have a built-in internal termination resistor which functions as the termination resistor on 

the master side. For details, refer to the operating manual for the master device.

*2 The termination resistor for RS-485 communication is built into the product.
*3 For the termination resistor on slave side, use a dedicated termination resistor for MECHATROLINK communication, 

manufactured by YASKAWA Electric Corporation.

 

„

CE Marking

The input power supply voltage of this product is 24 VDC. Therefore this product is not subject to the Low Voltage 
Directive, but install and connect it as follows.

 

•

This product is designed and manufactured to be incorporated in equipment. Be sure to install the product inside 
an enclosure.

 

•

For the power supply of the 

NETC01-M2

, use a DC power supply with reinforced insulation on its primary and 

secondary sides.

 

•

Overvoltage category: I

 

•

Pollution degree: 2

 

•

Degree of protection: IP20

 

z

EMC Directive

This product is conducted EMC testing under the conditions specified in “Example of 

NETC01-M2

 installation and 

wiring” on p.10.
The conformance of your mechanical equipment with the EMC Directive will vary depending on such factors as the 
configuration, wiring, and layout for other control system devices and electrical parts used with this product. It 
therefore must be verified through conducting EMC measures in a state where all parts including this product have 
been installed in the equipment.

Applicable standards

 

•

EMI: EN 55011 group 1 class A, EN 61000-6-4

 

•

EMS: EN 61000-6-2

This equipment is not intended for use in residential environments nor for use on a 
low-voltage public network supplied in residential premises, and it may not provide 
adequate protection to radio reception interference in such environments.

 

„

Republic of Korea, Radio Waves Act

This product is affixed the KC Mark under the Republic of Korea, Radio Waves Act.

 

„

RoHS Directive

The products do not contain the substances exceeding the restriction values of RoHS Directive (2011/65/EU).

Содержание NETC01-M2

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды