EN
INTRODUCTION
Thank you for selecting the Oregon Scientific™ PRYSMAchrome
Weather Station. This device bundles precise time keeping, alarm, and
temperature monitoring features into a single tool you can use from the
convenience of your home. Keep this manual handy as you use your
new product. It contains practical step-by-step instructions, as well as
technical specifications and warnings you should know.
LCD DISPLAY
Time Display
Outdoor/Indoor
temperature display
Weather
forecast display
Outdoor/Indoor
humidity display
Icon
Description
In humidity display area
( ): Low battery in remote
sensor
In time display area
( ): Low battery in main unit
backup battery (CR2032).
Remote sensor channel number
Temperature/humidity auto-loop indicator
Indoor temperature/humidity indicator
Humidity display indicator (%)
Temperature display indicator (°C/°F)
Alarm is on.
RCC signal reception indicator
OVERVIEW
TOP VIEW
- Press to toggle the alarm display and alarm on/off. Press and
hold to enter alarm setting.
- Press to toggle between time and date display. Press and hold
to enter the setting.
- Tap to snooze an alarm or activate the brightest
backlight for 5 seconds.
- Press to increase the value in setting, or press and hold to
increase a value rapidly in setting. Press to toggle the remote
sensor channels in ascending order, or press and hold to search
for the remote sensor.
- Press to decrease the value in setting, or press and hold to
decrease a value rapidly in setting. Press to toggle the remote
sensor channels in descending order, or press and hold to remove
selected remote sensor.
REAR VIEW
- Press to reset the unit to default.
- Press to turn on the RCC signal reception. Press and hold
to turn off.
- Micro USB power jack
- Press to toggle the temperature unit.
- Press to toggle the backlight brightness level. Press and
hold to set the back light color.
Remote sensor
CH
Channel 1-5. If more than one sensor is being used, make sure
each one has a different channel number.
SEARCH
Press to search for RCC function.
RESET
Press if the sensor is not working correctly, after battery
replacement or channel change.
GETTING STARTED
Connecting the main unit to power supply
Connect the power cable to the Micro USB jack and plug the power
adaptor into a suitable power outlet.
Inserting batteries into remote thermo sensor
1. Slide down the battery compartment cover to open, then insert 2
“AAA” batteries, matching the polarity as shown.
2. Press
. Slide to replace the battery compartment cover.
NOTE
The main unit can connect up to 5 sensors. Press and hold + on
the main unit to search for the remote sensor every time after adding
a new sensor.
Placement of the main unit
• Place the device as far as possible from computers and microwaves
to avoid any interference.
• Only use this device indoors in a dry location.
• Leave space around the device for ventilation purposes.
• To ensure for good sound quality, do not cover the speaker.
Placement of the remote thermo sensor
Min 5 ft (1.5 m)
Max 164 ft (50 m)
Place your sensor outside the home at a height of not less than 5 ft
(1.5 m), shielded from direct sunlight or wet conditions.
• The
icon on the main unit flashes while searching the signal
from the remote sensor.
NOTE
The radio signal reaches up to 164 ft (50 m) depending on
conditions of surrounding.
Replacing CR2032 backup battery
This unit is equipped with a CR2032 battery as a backup power source
to recover the clock and alarm settings when reconnected to mains
supply. When the main unit shows , replace the CR2032 backup
battery.
To replace a CR2032 backup battery
1. Open up the bottom left corner of the rubber cover, then gently
push the arched part of the backup battery door downwards as
shown above.
2. Replace the CR2032 backup battery to the compartment, then push
the battery compartment back into the main unit. Connect the main
unit to the power supply and then press
.
NOTE
When replacing the backup battery, flip the bottom left corner
rubber cover only. Do not remove the entire rubber cover.
TEMPERATURE SENSITIVE LCD DISPLAY
The LCD display changes colors according to the temperature of the
first sensor with the lowest channel number available (e.g channel 1). If
sensor channel 1 is not available, the LCD display will change its color
according to the temperature of the next sensor channel (e.g. channel
2) available in ascending order.
You may also set the LCD display color manually by press and hold
, then press or to toggle between the desired color number,
or choose
Auto
to change colors according to the temperature.
Outdoor Temperature (Channel 1)
Color
Color number
≤ 5.9 °C
Purple
1
6 °C - 10.9 °C
Blue
2
11 °C - 15.9 °C
Pale blue
3
16 °C - 20.9 °C
Green
4
21 °C - 25.9 °C
Yellow
5
26 °C - 30 °C
Orange
6
≥30.1°C
Red
7
• Tab
to activate the brightest backlight (LV. 3) display
for 5 seconds.
• Press
repeatedly to toggle the desired backlight display
brightness level (LV. 1/LV. 2/LV. 3).
• The unit might take some time to change its LED display color.
RADIO RECEPTION
This unit is designed to automatically synchronize its calendar and
clock when brought within the range of the radio signal. The main unit is
able to receive RF clock data in different RCC signals from the sensors
depend on the region:
Region
Signal
EU
DCF
UK
MSF
US
WWVB
Depending on the strength of the signal, the connection process
takes 2 to 10 minutes. If the signal is weak, it could take up to 24
hours to receive a valid signal.
BAR292/BAR292A
Symbol
Description
RCC is off
RCC Time is received
No RCC signal received
NOTE
The default time zone setting is Central (
C
) for the US and +/-
0
for the EU/UK. Check your time zone setting before receiving the RCC
signal.
SETTING TIME MANUALLY
1. Press and hold . The screen displays
and the number
flashes.
2. Press once or press and hold or to adjust the setting. For
EU/UK, the time-zone offset sets the clock up to +/- 23 hours from
the received clock signal time. For US, the time-zone setting is
Central (
C
); Eastern (
E
); Atlantic (
A
); Newfoundland (
N
); Pacific (
P
);
Mountain (
M
).
3. Press to confirm.
4. Press once or press and hold or to adjust the setting for 12/24
hour format, hour, minute, year, calendar format (month-day/day-
month), month, date and daylight saving time (
DST
) auto/off.
5. Press again to confirm.
NOTE
• The daylight saving time (
DST
) setting is available for the United
States only.
• The RCC and daylight saving time (
DST
) are disabled when the
time/year, month or date is changed in the setting. The DST is also
disabled when the RCC is turned off. If you turn the RCC back on,
the DST resumes from the last setting.
• While in the setting mode, press and hold to save the settings
and return to idle.
ALARM FUNCTION
Setting/adjusting alarm time
1. Press and hold .
2. Use and to adjust the hour and press to confirm.
3. Use and to adjust the minute and press to confirm.
4. The alarm icon displays in idle. When the alarm sounds, it lasts for
2 minutes.
NOTE
While in the alarm setting mode, press to save the settings
and leave the alarm setting mode.
Snooze function
• To use the snooze function, press the
on top of the clock
when the alarm sounds. The alarm will stop and start again after 8
minutes.
Activating/deactivating the alarm
• Press to turn on the alarm, press twice to turn off the alarm.
• When the alarm sounds, press to stop the alarm. The alarm will
reactivate on the next day.
WEATHER FORECAST
This product forecasts the next 12 hours of weather in nearby area.
Screen display
Description
Sunny
Partly cloudy
Cloudy
Rainy
Snowy
TEMPERATURE AND HUMIDITY FUNCTION
The current outdoor/indoor temperature and humidity indicators locate at
top and bottom left of the screen. To receive outdoor temperature and
humidity information, you can connect up to 5 remote sensors to the main
unit:
• Press or to toggle sensor display.
NOTE
When the indoor temperature is lower than -5 °C (23.0 °F), the
screen displays
LL.L
. When it is higher than 50 °C (122.0 °F), the screen
displays
HH.H
.
When the indoor relative humidity is lower than 25%, the screen displays
LL
. When it is higher than 95%, the screen displays
HH
.
To auto-loop between sensors
:
Press or repeatedly until displays. The data on each sensor
displays for 3 seconds. Press +/-again turn off the auto-loop, the icon
turns off.
NOTE
The sensor displays in ascending order. The main unit skips the
absent sensor and advances to the next present sensor.
To search for remote sensors:
Press and hold .
To remove selected sensor:
Press and hold .
TROUBLESHOOT
Problem
Reason
Solution
The main unit
does not display
at all.
The main unit is not
connected to the
power outlet.
Make sure the main unit is
connected with the power
adapter.
The outdoor display
area is blank.
The outdoor sensor is
removed.
Reconnect the outdoor sensor.
The outdoor
display area
displays ---.
The main unit is unable
to receive data from
the remote sensor.
Check the connection between
the main unit and the sensor.
The main unit
does not receive
RCC signal.
The RCC signal
reception might
experiencing
interference.
Make sure both main unit and
the sensor are ready to receive
the RCC signal. Press
on the sensor and press
on
the main unit to turn on the RCC
signal reception.
The main unit
does not display
properly.
The main unit is unable
to receive data from
the remote sensor.
Press
to reset the
main unit.
PRECAUTIONS
• Do not subject the unit to excessive force, shock, dust, temperature
or humidity.
• Do not immerse the unit in water. If you spill liquid over it, dry it
immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not tamper with the unit’s internal components. This invalidates
the warranty.
• Only use fresh batteries. Do not mix new and old batteries.
• Images shown in this manual may differ from the actual display.
• When disposing this product, ensure it is collected separately for
special treatment.
• Placement of this product on certain types of wood may result
in damage to its finish for which Oregon Scientific will not be
responsible. Consult the furniture manufacturer’s care instructions
for information.
• The contents of this manual may not be reproduced without the
permission of the manufacturer.
• Do not dispose old batteries as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
• Please note that some units are equipped with a battery safety strip.
Remove the strip from the battery compartment before first use.
NOTE
The technical specifications for this product and the
contents of the user manual are subject to change without notice.
To download an electronic copy of this user manual, please visit
http://global.oregonscientific.com/customerSupport.php.
SPECIFICATIONS
MAIN UNIT
L x W x H
22 x 200 x 80 mm
Weight
224 g without batteries
Temperature range
-5.0 °C to +50.0 °C (23.0 °F to 122.0 °F)
Temperature accuracy
0°C to 40°C: ±1°C (± 2.0°F)
T<0°C : ±2°C (± 4.0°F)
T>40°C : ±2°C (± 4.0°F)
Temperature resolution
0.1°C (0.2°F)
Relative humidity
measurement
25% to 95% RH
Humidity accuracy
40% to 80% RH: ±5%
25% to 40% RH: ±7%
80% to 95% RH: ±7%
Power
5V adapter
CR2032 backup battery
REMOTE UNIT (RTGN130/RTGN130A)
L x W x H
125 x 50 x 19.5 mm
Weight
59 g without batteries
Transmission range
50 m (164 ft) unobstructed
Temperature range
-20 °C to 60 °C (-4 °F to 140 °F)
Temperature accuracy
0°C to 40°C: ±1°C (± 2.0°F)
T<0°C : ±2°C (± 4.0°F)
T>40°C : ±2°C (± 4.0°F)
Temperature resolution
0.1 °C (0.2 °F)
Relative humidity
measurement
25% to 95% RH
Humidity accuracy
40% to 80% RH: ±5%
25% to 40% RH: ±7%
80% to 95% RH: ±7%
Signal frequency
433 MHz
No. of channel selectable
5
ABOUT OREGON SCIENTIFIC
Visit our website www.oregonscientific.com to learn more about
Oregon Scientific products.
For any inquiry, please contact our Customer Services at
Oregon Scientific Global Distribution Limited reserves the right to
interpret and construe any contents, terms and provisions in this
user manual and to amend it, at its sole discretion, at any time
without prior notice. To the extent that there is any inconsistency
between the English version and any other language versions, the
English version shall prevail.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the nterference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or
sales. Please call our customer service number (listed on our website
at www.oregonscientific.com),
or on the warranty card for this product for all inquiries instead.
We
Name:
Oregon Scientific, Inc.
Address:
Brea Corporate Park
3020 Saturn St. Suite 200
Brea, CA 92821
Telephone No.:
1-800-853-8883
declare that the product
Product No.:
BAR292/BAR292A
Product Name:
PRYSMAchrome
Manufacturer:
IDT Technology Limited
Address:
Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong
EU-DECLARATION OF CONFORMITY
Hereby, IDT Technology Limited, declares that this PRYSMAchrome
Weather Station (Model: BAR292/BAR292A) is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU. A copy of the signed and dated Declaration of Conformity
is available on request via our Oregon Scientific Customer Service.
COUNTRIES RED APPROVED COMPLIED
All EU countries, Switzerland
and Norway
N
CH
DISPOSAL INFORMATION FOR USERS
Pursuant to and in accordance with Article 14 of the Directive
2012/19/EU of the European Parliament on waste electrical
and electronic equipment (WEEE), and pursuant to and in
accordance with Article 20 of the Directive 2006/66/EC of the
European Parliament on batteries and accumulators and waste
batteries.
The barred symbol of the rubbish bin shown on the equipment indicates
that, at the end of its useful life, the product must be collected separately
from other waste.
Please note that the batteries/rechargeable batteries must be removed
from the equipment before it is given as waste. To remove the batteries/
accumulators refer to the specifications in the user manual. Therefore,
any products that have reached the end of their useful life must be given
to waste disposal centers specializing in separate collection of waste
electrical and electronic equipment, or given back to the dealer when
purchasing a new WEEE, pursuant to and in accordance with Article 14
as implemented in the country.
The adequate separate collection for the subsequent start-up of
the equipment sent to be recycled, treated and disposal of in an
environmentally compatible way contributes to preventing possible
negative effects on the environment and health and optimizes the
recycling and reuse of components making up the apparatus.
Abusive disposal of the product by the user involves application of the
administrative sanctions according to the laws in force.
BAR292_UM AEA 300103818-00005-10 R1.indd 1
2017/7/31 下午3:18
Содержание PRYSMAchrome BAR292
Страница 1: ...BAR292 BAR292A...
