Oreck XL3 Скачать руководство пользователя страница 5

5

  

H

 

S

 

I

 

L

 

G

 

N

 

E

General  

Information  

The performance of your new cleaner greatly depends upon care and maintenance. The instructions 

in this manual will guide you in performing basic care and maintenance. To obtain the most 

satisfying years of service read the instructions and keep them handy for future reference. 

Disposable Dust Bags 

Disposable Filter Dust Bags play a very important role in the efficiency of your ORECK vacuum cleaner.

The purpose of the dust bag is to trap dirt, but at the same time it must be porous enough to allow 

air to pass through. If the dust bag becomes clogged, no air can pass through the cleaner and 

cleaning cannot take place, regardless of the cleaner’s power. 

DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG. 

not the same. Your ORECK Disposable Dust Bags have been designed to be used with the ORECK 

cleaner. Using bags other than genuine ORECK TYPE CC disposable bags will affect the cleaning 

ability of your cleaner and could cause damage to it and will void the warranty. 

Celoc

®

Filtration System 

smallest of dust particles. It is important that the inside of the Outer Bag be cleaned. Vacuum the inside  

of the Outer Bag or hand wash, turned inside out, with warm water, and air dry. If desired, the Celoc

®

  

replaced once a month even if it is not full. Change it more often if it is used in extremely dirty areas. 

Increase the cleaning power of your vacuum by changing the bag often. 

The Belt 

The belt on your vacuum cleaner controls the speed of the revolving brush and is very important 

for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the 

revolving brush to stop completely or slow down. See page 6 for replacing worn belt. 

Note:

An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use 

ONLY ORECK genuine belts. Belts other than Oreck belts will not operate the revolving brush 

correctly and may create undue stress which will cause damage to the motor and brush bearings. 

Using belts other than ORECK belts will void the warranty. 

Lubrication 

The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required.   

CAUTION  

Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished  

Floor Finishes  

operate the unit while in the upright and locked position. Do not let 

the unit run while in any one stationary position for any period of 

time. Keep the unit moving while in operation. 

Note:

At least once a month, check for and remove excessive lint, 

string or hair from revolving brush. 

Wipe the outside of the cleaner with a damp cloth. Also clean the Connector 

Assembly area, base of cleaner and fan housing area. If there is 

dust in the outer bag, vacuum it or shake it out.  
A little preventative maintenance will keep your cleaner looking new 

and will ensure continued cleaning effectiveness. 

  

Be sure the Disposable Filter Dust Bag is installed properly. Note: All Disposable Filter Dust Bags are 

WARNING: 

Unplug Power Cord from electrical socket before servicing.  

The Celoc

®

 Outer Bag of your vacuum cleaner is high filtration medical material designed to filter the 

Outer Bag can be replaced for renewed efficiency. The Celoc

®

 

layered Disposable Filter Dust Bag must be

Содержание XL3













Отзывы: