manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 97

Preparing for Service

These topics describe how to prepare the server for servicing. The sections describe safety

considerations and provide prerequisite procedures and information about replacing

components within the server.

Section Description

Link

Procedures for creating an ESD-safe work

space

“Performing Electrostatic Discharge and Static Prevention

Measures” on page 98

Required tools

“Required Tools and Equipment” on page 100

Setting up for service

“Preparing the Server for Component Replacement” on page 101

Setting up for hot service

“Prepare the Server for Hot Service (Oracle ILOM

CLI)” on page 103

“Prepare the Server for Hot Service (Oracle ILOM Web

Interface)” on page 104

Setting up for warm service

“Prepare the Server for Warm Service (Oracle ILOM

CLI)” on page 105

“Prepare the Server for Warm Service (Oracle ILOM Web

Interface)” on page 107

Setting up for cold service

“Prepare the Server for Cold Service (Oracle ILOM

CLI)” on page 108

“Prepare the Server for Cold Service (Oracle ILOM Web

Interface)” on page 110

Server power-off options

“Powering Down the Server” on page 111

Methods for activating and deactivating the

server Locate Button/LED

“Managing the Locate Button/LED” on page 120

Review the 

Oracle Server X7-8 Product Notes Release 1.0

 for hardware-related information

before performing removal and installation procedures.

Preparing for Service

97

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды