Oracle X7-8 Скачать руководство пользователя страница 110

Страница: 110 / 308

Prepare the Server for Cold Service (Oracle ILOM Web Interface)

See

“Servicing Components” on page 123

Prepare the Server for Cold Service (Oracle ILOM

Web Interface)

This procedure describes how to prepare the server for cold service when you remove, replace,

or install cold-serviceable components. A cold-service component must be serviced when

the server is completely powered off and AC cords have been removed from the back panel

AC power block. For more information about component serviceability, see

“Component

Serviceability Requirements” on page 26

This procedure is performed locally and requires physical access to the server front and back

panels.

Log in to the service processor Oracle ILOM web interface.

Direct a web browser to Oracle ILOM using the IP address of the server SP and log in as root

or a as user with administrator privileges. See

“Accessing Oracle ILOM” in

Oracle Server X7-8

Installation Guide

The Summary Information page appears.

In the Actions section of the Summary Information page, verify that the Power

State is ON.

If the Power State status shows off, the server is already powered off.

Power down the server. In the Actions section of the Summary Information page,

click the Power State Turn Off button.

This action powers off the server to Standby power mode. For more power off options, see

“Powering Down the Server” on page 111

In the Actions section of the Summary Information page, click the Locator

Indicator Turn On button.

110

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды