Oracle X7-8 Скачать руководство пользователя страница 244

Страница: 244 / 308

Using UEFI BIOS

Using UEFI BIOS

Oracle Server X7-8 is equipped with a Unified Extensible Firmware Interface (UEFI)-

compatible BIOS, which runs with all operating systems that are supported on the server. The

BIOS firmware controls the system from power-on until an operating system is booted and

allows you to configure, enable, disable, or manage system components.

This section includes the following information:

■

“Configuration Utilities for Add-In Cards” on page 244

■

“Configure and Manage BIOS Using Oracle ILOM” on page 244

■

“UEFI Secure Boot” on page 245

■

“Trusted Execution Technology” on page 245

Configuration Utilities for Add-In Cards

In UEFI BIOS, the configuration screens for the add-in cards will appear as menu items in

the BIOS Advanced Menu as part of the standard BIOS Setup Utility screens. For example,

if the Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal card is installed in the server, the

configuration utility for the HBA appears as a menu selection.

Configure and Manage BIOS Using Oracle ILOM

Oracle Integrated Lights Out Manager (ILOM) includes BIOS configuration and management

tools. You can perform the following BIOS configuration tasks using Oracle ILOM:

■

View the BIOS configuration synchronization status and synchronize the configuration

parameters

■

Reset the factory defaults for the service processor (SP) and Oracle ILOM BIOS

■

Backup or restore the BIOS configuration

■

Enable UEFI diagnostics to run at system boot

For more information about Oracle ILOM BIOS configuration and management tools, refer to

the Oracle Integrated Lights Out Manager (ILOM) 4.0 Documentation Library at:

http://www.

oracle.com/goto/ilom/docs

244

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды