Oracle X7-8 Скачать руководство пользователя страница 19

Страница: 19 / 308

About Controls and Connectors

Feature

System Component

For updated operating system informaiton, refer to the

Oracle Server X7-8 Product Notes

http://

www.oracle.com/goto/x7-8/docs

For server specification information, see

“Server Features and Components” in

Oracle Server

X7-8 Installation Guide

For component serviceability, locations, and designations, see

“Identifying

Components” on page 24

About Controls and Connectors

The following sections describe the controls, indicators, connectors, and drives located on the

Oracle Server X7-8 front and back panels.

■

“Front Panel Components” on page 19

■

“Back Panel Components” on page 21

Front Panel Components

The following figure shows the Oracle Server X7-8 chassis front panel components:

About the Oracle Server X7-8

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды