Oracle X7-8 Скачать руководство пользователя страница 138

Страница: 138 / 308

Servicing Power Supplies (CRU)

Position the fan frame at the opening in the front of the server with the air vane

hinges at the top.

Note -

The center of the fan frame is marked with green labels. The labels indicate where to

grab the frame when you want to install or remove it.

Slide the fan fame into the server until it stops and is flush with the front of the

server.

Install the four FMs. See

“Install a Fan Module” on page 133

Prepare the server for operation.

See

“Identifying Components” on page 24

Servicing Power Supplies (CRU)

This section describes how to service power supplies (PS). Power supplies are customer-

replaceable units (CRUs) that do not require you to power off the server. For more information

about CRUs, see

“Illustrated Parts Breakdown” on page 24

and

“Customer-Replaceable

Units” on page 26

138

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды