Oracle X7-2 Скачать руководство пользователя страница 54

Страница: 54 / 148

Install the Cable Management Arm (Optional)

the server into the rack until the slide-rail locks (on the front of the mounting

brackets) engage the slide-rail assemblies with an audible click.

Caution -

Before you install the optional cable management arm verify that the server is

securely mounted in the rack and that the slide-rail locks are engaged with the mounting

brackets.

Related Information

■

“Install the Cable Management Arm (Optional)” on page 54

Install the Cable Management Arm (Optional)

Follow this procedure to install the cable management arm (CMA), which you can use to

manage cables connected to the back of the server.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Содержание X7-2





















































































































































Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды

Oracle X7-2, Руководство по установке

Результаты поиска

Содержание X7-2

Отзывы:

Похожие инструкции для X7-2

Бренды по названию

Популярные бренды