Oracle X7-2 Скачать руководство пользователя страница 13

Страница: 13 / 148

Preparing for Server Installation

These sections provide the information you need to prepare for the server installation.

■

“Server Physical Specifications” on page 13

■

“Receiving and Unpacking Requirements” on page 14

■

“Rack Space Requirements” on page 14

■

“Maintenance Space Requirements” on page 15

■

“Environmental Requirements” on page 15

■

“Ventilation and Cooling Requirements” on page 17

■

“Electrical Requirements” on page 18

■

“Agency Compliance” on page 20

■

“Shipping Inventory” on page 21

■

“Tools and Equipment” on page 22

■

“Optional Component Installation” on page 22

■

“PCIe Cards” on page 23

Server Physical Specifications

The following tables list the physical specifications for the Oracle Server X7-2 and Oracle

Server X7-2L.

Oracle Server X7-2

Dimension

Server Specification

Measurement

Width

Server chassis

48.2 cm (18.9 inches)

Depth

Maximum overall

73.70 cm (29.02 inches)

Height

1-rack unit (1U) nominal

4.26 cm (1.68 inches)

Preparing for Server Installation

Содержание X7-2





















































































































































Результаты поиска

Содержание X7-2

Отзывы:

Oracle X7-2, Руководство по установке, Страница: 13 / 148

Результаты поиска

Содержание X7-2

Отзывы: