manualshive.com logo in svg

Oracle Tekelec 1200, Руководство по установке

Поделиться
Скачать
Oracle Tekelec 1200 Скачать руководство пользователя страница 47

Procedure — Optional Hoist with Crane

Another option to unpack the cabinet is to remove the cabinet from the pallet and lower it to the floor
using hoisting eyebolts and a crane. Use this method if there is not enough room to open the crate and
use the door ramp.

Warning:  To avoid physical injury, be sure that properly rated hoisting equipment is
used. When hoisting the cabinet, pull straight up slowly on the eyebolts using properly
rated hardware attached evenly to the eyebolts to prevent the cabinet from swinging.
Always secure the cabinet during lifting to minimize swing.

1. Remove crate lid.

2. Screw the eyebolts completely into the top of the cabinet.

3. Securely attach the eyebolts to a hoist. The hoist should be positioned so that the four eyebolts

evenly support the weight of the cabinet.

4. Use the 15/16” socket wrench with 15/16” drive ratchet to unbolt the cabinet from the crate.

5. Using a crane, carefully lift the cabinet off the pallet and lower the cabinet into its final position

over the anchor holes drilled in the floor.

Minor manual adjustments may be necessary to ensure correct alignment of the cabinet to anchor
sites.

Installing the Cabinet

You must bolt the seismic cabinet to a floor using the anchors provided. The following steps are
required to install the cabinet.

•

Procedure — How to Mark the Floor Layout

•

Procedure — Prepare Raised Floor for Anchors

•

Procedure — Drill Cable Holes

•

Procedure — Cabinet Anchoring

•

Procedure — Raised Floor Earthquake Bracing

•

Procedure — Anchor Cabinet on Concrete Floor

• Install kick plates (see 

Figure 22: Kick Plates

) with 10 mm allen wrench

47

910-5681-001 Revision E, February 2014

Cabinet Installation

Installation

Содержание Tekelec 1200













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды