Oracle Sun Netra X4270 Скачать руководство пользователя страница 190

Страница: 190 / 238

Install Fan Tray 0

Remove the fan tray cable from the cable guides on the air duct.

Insert your forefinger and thumb into the holes at the top of the fan tray, squeeze

your fingers together, and lift the fan tray from the chassis.

Set the fan tray on an antistatic mat.

Consider your next step:

■

If you removed the fan assembly as part of another procedure, return to that procedure.

■

Otherwise, continue to

“Install Fan Tray 0” on page 190

Related Information

■

“Replacing the Air Duct” on page 127

■

“Replacing DIMMs” on page 132

■

“Replacing CPUs” on page 160

■

“Install Fan Tray 0” on page 190

Install Fan Tray 0

Remove the replacement fan tray from its packaging and place it on an antistatic

mat.

190

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды