manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 152

Remove ESM Riser

See 

“Remove ESM Riser” on page 152

 and 

“Install ESM Riser” on page 154

.

■

If the ESM has failed, replace the ESM.
See 

“Replace the ESM” on page 155

■

If both components have failed, replace both components.
See 

“Remove ESM Riser” on page 152

 and 

“Install ESM Riser” on page 154

.

Remove ESM Riser

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

2.

Remove the PCI mezzanine and place it on an antistatic mat.

See 

“Remove the PCI Mezzanine” on page 102

.

3.

Remove the air duct and place it on an antistatic mat.

See 

“Remove the Air Duct” on page 127

.

152

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды