Oracle Sun Netra X4270 Скачать руководство пользователя страница 142

Страница: 142 / 238

Install DIMMs

Align the notch in the DIMM with the key in the connector. The notch ensures that the DIMM

is oriented correctly.

Push the DIMM into the connector until the ejector tabs lock the DIMM in place.

If the DIMM does not easily seat into the connector, verify that the notch in the DIMM is

aligned with the key in the connector. If the notch is not aligned, damage to the DIMM might

occur.

until all replacement DIMMs are installed.

Consider your next step:

■

If you installed DIMMs as part of another procedure, return to that procedure.

■

If you are only installing new or replacing faulty DIMMs, continue to the next step.

Install the media bay assembly.

See

“Install the Media Bay Assembly” on page 97

Install the air duct.

See

“Install the Air Duct” on page 130

10.

Return the server to operation.

See

“Returning Server to Operation” on page 211

142

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды