Oracle Sun Netra X4270 Скачать руководство пользователя страница 118

Страница: 118 / 238

Remove the SAS Controller HBA

Return the server to operation.

See

“Returning Server to Operation” on page 211

Connect any external cable to the PCIe2 card.

Refer to your PCIe2 card documentation for more information.

Related Information

■

“PCIe2 Slot Characteristics” on page 112

■

“PCI Mezzanine Auxiliary Power Connector” on page 114

■

“Remove PCIe2 Cards From Slots 4 and 5” on page 115

Replacing the SAS Controller HBA

These topics describe how to remove and install the SAS controller HBA. Refer to the SAS

controller HBA documentation for complete cabling and software information.

■

“Remove the SAS Controller HBA” on page 118

■

“Install the SAS Controller HBA” on page 120

Related Information

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

■

“Replacing Lower PCIe2 Cards” on page 123

Remove the SAS Controller HBA

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Locate the SAS controller HBA on the PCI mezzanine.

The HBA is installed in the right-most slot on the PCI mezzanine.

118

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды