Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 81 / 188

Verify a Fan Module

Related Information

■

“Return the Server to the Normal Operating Position” on page 173

■

“Remove a Fan Module” on page 77

■

“Verify a Fan Module” on page 81

Verify a Fan Module

Verify that the Service Required LED on the replaced fan module is not lit.

See

“Fan Module LEDs” on page 76

At the Oracle ILOM prompt, start the fault management shell.

start /SP/faultmgmt/shell

Are you sure you want to start /SP/faultmgmt/shell (y/n)?

faultmgmtsp>

Type

fmadm faulty

to check for faults.

■

If faults are reported, see

“Detecting and Managing Faults” on page 27

■

If no faults are reported, then the component has been replaced successfully.

Consider these possibilities:

■

If any of the LEDs are illuminated, see

“Interpreting LEDs” on page 33

■

If none of the LEDs are illuminated, the fan module has been replaced successfully.

Related Information

■

“Determine Which Fan Module Is Faulty” on page 77

■

“Front Panel Components (Service)” on page 13

■

“Rear Panel Components (Service)” on page 15

Servicing Fan Modules

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды