Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 199 / 258

Servicing the Drive Power Cable

Route the cable to the SAS drive signal cable connector on the drive backplane.

Install the air duct.

See

“Install the Air Duct” on page 236

Install the fan tray and all fan modules.

See

“Install the Fan Tray” on page 244

Connect the SAS drive signal cable connector to the drive backplane.

See

“Cable Configurations” on page 194

If you installed a cable as part of another component's removal or installation

procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

for assistance.

Finish the installation procedure.

See

“Returning a Server to Operation” on page 235

Related Information

■

“Remove the SAS Drive Signal Cable” on page 196

■

“Component Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

■

“Component Locations (Motherboard, Memory, and PCIe Cards)” on page 16

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Servicing the Drive Power Cable

These topics describe how to remove and install the drive power cable.

Description

Links

Replace a faulty cable.

“Detecting and Managing Faults” on page 25

“Remove the Drive Power Cable” on page 200

“Install the Drive Power Cable” on page 202

Remove a cable as part of another component's

service operation.

“Remove the Drive Power Cable” on page 200

Servicing the Cables

199

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды