Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 191 / 258

Install the Battery

Install the Battery

Installing the battery is a cold-service operation. You must power off the server before installing

the battery.

If you have not done so already, prepare for service and remove the battery.

See:

■

“Preparing for Service” on page 43

■

“Remove the Battery” on page 189

Press the battery into the receptacle until you hear a click.

The positive (+) side of the battery faces toward the PCIe card slots 1-4.

If you installed the battery as part of another component's removal or installation

procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

for assistance.

Finish the installation procedure.

See

“Returning a Server to Operation” on page 235

Set the date and time on SP and Host OS.

Restore the Oracle ILOM variables.

See

http://docs.oracle.com/cd/E19860-01/E21549/z40015841018582.html#scrolltoc

Related Information

■

“Remove the Battery” on page 189

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Servicing the Battery

191

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды