Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 176 / 258

Install a PCIe Card

See

“Install a PCIe Card” on page 176

Power on the server.

See

“Returning a Server to Operation” on page 235

Related Information

■

“Locate a Faulty PCIe Card” on page 172

■

“Install a PCIe Card” on page 176

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Install a PCIe Card

Installing a PCIe card is a cold-service operation. You must power off the server before

installing the PCIe card.

Note -

This procedure is the same for installing a PCIe filler.

If you are installing additional cards, review this information and complete these

prerequisites in this order.

See:

■

“PCIe Card Configurations” on page 170

■

“Preparing for Service” on page 43

■

“Remove a PCIe Card” on page 174

Remove the filler.

If you are replacing a faulty card and have not removed the faulty card, remove it

and return to this procedure.

See

“Remove a PCIe Card” on page 174

If not already done, prepare for service.

See

“Preparing for Service” on page 43

Position the PCIe card at the slot where it will be installed.

Press the PCIe card into the socket.

176

Netra SPARC S7-2 Server Service Manual • February 2017

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды