Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 152 / 258

Locate a Faulty Fan Module

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Locate a Faulty Fan Module

You must determine which fan module is faulty before you replace it.

Check to see if any System Service Required LEDs are lit or flashing.

See

“Front Panel Components (Service)” on page 17

In Oracle ILOM, check the health of the cooling system.

show /System/Cooling

/System/Cooling
Targets:
Properties:
health = OK
health_details = -
...
->

Verify that a fan module is faulty.

For example, type:

show faulty

Target | Property | Value
--------------------+------------------------+-------------------------------
/SP/faultmgmt/0 | fru | /SYS/MB/FM0
...
->

If a fan module is faulty, you will see

/SYS/MB/FM

under the

Value

heading where

If a FRU value different from

/SYS/MB/FM

is displayed, see

“Component Service Task

Reference” on page 47

to identify which component is faulty.

Use the Oracle ILOM

faultmgmt

shell to identify the faulty component.

See

“Identify Faulted Components” on page 27

Check the

Fault class

and

Description

fields for more information.

Within the Oracle ILOM interface, verify the fan module speeds.

152

Netra SPARC S7-2 Server Service Manual • February 2017

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды