Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 24

Страница: 24 / 102

Airflow Precautions

Related Information

■

“Physical Specifications” on page 17

■

“Electrical Specifications” on page 18

■

“Input Power Information” on page 19

■

“DC Power Source, Power Connection, and Grounding Requirements” on page 21

■

“Overcurrent Protection Requirements” on page 20

■

“Environmental Requirements” on page 22

■

“Airflow Precautions” on page 24

Airflow Precautions

Caution -

Proper airflow is essential for keeping the server's internal temperatures within a safe

operating range.

Air flows from the front to the rear of the server.

Follow these guidelines to ensure unrestricted airflow in the server:

■

Adhere to the minimum airflow clearance specifications. See

“Physical

Specifications” on page 17

■

Install the server so the front faces the cool aisle and the rear faces the warm aisle.

■

Do not direct warm air into the server.

■

Prevent recirculation of air within a rack or cabinet.

■

When servicing server internal components, ensure that air ducts, baffles, and filler panels

are properly installed.

■

Route cables so they do not interfere with airflow.

Netra SPARC S7-2 Server Installation Guide • January 2017

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды